Difference between revisions of "ATLB - AlphaCom Telephone Line Board"
From Zenitel Wiki
(57 intermediate revisions by 4 users not shown) | |||
Line 1: | Line 1: | ||
− | [[ | + | {{obsolete}} |
− | == | + | [[Image:9102 RS.jpg|thumb|250px|ATLB Telephone Line Board]] |
+ | |||
+ | ATLB is replaced by the [[ATLB-12 - AlphaCom Telephone Line Board|ATLB-12 board]]. | ||
+ | |||
+ | == Highlights == | ||
* Is used for 2-wire connection of telephones as stations in an AlphaCom system | * Is used for 2-wire connection of telephones as stations in an AlphaCom system | ||
* Each board provides 6 telephone connections and 1 voice-switched conversation | * Each board provides 6 telephone connections and 1 voice-switched conversation | ||
Line 10: | Line 14: | ||
* 600 ohm or complex impedance hybrid balance | * 600 ohm or complex impedance hybrid balance | ||
* Line monitoring using resistor in parallel with phone | * Line monitoring using resistor in parallel with phone | ||
− | * Hot plug in and out of the board | + | * [[Hot-plug]] in and out of the board |
* Red/green/amber LED indicates system status | * Red/green/amber LED indicates system status | ||
− | |||
− | = | + | <br style="clear:both;" /> |
− | |||
− | |||
− | |||
− | |||
− | |||
− | + | ==Additional Documentation== | |
− | + | For more documentation please see http://www.zenitel.com/product/atlb | |
− | |||
− | |||
− | + | ==Jumpers== | |
− | + | [[image:ATLB ATLB card with jumpers.jpg|thumb|left|500px|ATLB card with jumpers]] | |
− | + | <br style="clear:both;" /> | |
− | |||
− | |||
− | |||
− | |||
− | |||
== Connection Boards == | == Connection Boards == | ||
− | |||
− | |||
The standard connection board provides connection for 6 analogue telephones and 6 RCO outputs. | The standard connection board provides connection for 6 analogue telephones and 6 RCO outputs. | ||
− | The | + | The ATLB provides connection for 6 analogue telephones and 6 RCO outputs. In addition the board provides protection against heavy transients and a ring voltage generator. This board is used when the subscriber cabling may be exposed to heavy transients and should always be used if there are outdoor cables. The ring voltage generator is needed when there are several phones in parallel on the same line, or the lines are very long. |
− | protection against heavy transients and a ring voltage generator. This board is used when the subscriber cabling | + | |
− | may be exposed to heavy transients and should always be used if there are outdoor cables. The ring voltage | + | [[image:9930202 RS.jpg|thumb|left|500px|Connection Board ATLB]] |
− | generator is needed when there are several phones in parallel on the same line, or the lines are very long. | + | <br style="clear:both;" /> |
+ | |||
+ | [[image:Connection Board ProtRing ATLP.jpg|thumb|left|500px|Connection Board Prot/Ring ATLP]] | ||
+ | <br style="clear:both;" /> | ||
=== AlphaCom E20/E26 === | === AlphaCom E20/E26 === | ||
− | Telephones and control outputs are connected to a connection | + | Telephones and control outputs are connected to a connection board mounted on the exchange connection field. |
− | board mounted on the exchange connection field. | ||
− | Telephone connection board with transient protection (100 9930 | + | Telephone connection board with transient protection (100 9930 202) and subscriber connection cable with filter board (100 9501 031) must be purchased separately. |
− | 202) and subscriber connection cable with filter board (100 9501 | ||
− | 031) must be purchased separately. | ||
=== AlphaCom E7 === | === AlphaCom E7 === | ||
− | All telephones are connected by means of pluggable screw | + | All telephones are connected by means of pluggable screw terminals on the exchange back-plane. |
− | terminals on the exchange back-plane. | + | |
+ | '''Note:''' When the ATLB board is used in [[ATLB in AlphaCom E7 - RCO's|AlphaCom E7 only four RCO's]] are available. | ||
== Installation Overview == | == Installation Overview == | ||
− | [[image:ATLB Telephone connection to ATLB.jpg|thumb|left| | + | [[image:ATLB Telephone connection to ATLB.jpg|thumb|left|500px|Telephone connection to ATLB in XE20 and XE26]] |
− | [[image:ATLB Telephone connection to ATLB in E7.jpg|thumb|left| | + | [[image:ATLB Telephone connection to ATLB in E7.jpg|thumb|left|500px|Telephone connection to ATLB in XE7]] |
− | [[Category: | + | |
+ | <br style="clear:both;" /> | ||
+ | |||
+ | ==Related articles== | ||
+ | * [[Force analog phone to go on-hook by tone]] | ||
+ | |||
+ | [[Category:Discontinued Servers]] |
Latest revision as of 13:48, 14 June 2018
ATLB is replaced by the ATLB-12 board.
Contents
Highlights
- Is used for 2-wire connection of telephones as stations in an AlphaCom system
- Each board provides 6 telephone connections and 1 voice-switched conversation
- 6 remote control outputs (software configurable activation)
- Hotline function
- DTMF dialing
- R-button detection
- Selectable -48V or -24V battery feed
- 600 ohm or complex impedance hybrid balance
- Line monitoring using resistor in parallel with phone
- Hot-plug in and out of the board
- Red/green/amber LED indicates system status
Additional Documentation
For more documentation please see http://www.zenitel.com/product/atlb
Jumpers
Connection Boards
The standard connection board provides connection for 6 analogue telephones and 6 RCO outputs.
The ATLB provides connection for 6 analogue telephones and 6 RCO outputs. In addition the board provides protection against heavy transients and a ring voltage generator. This board is used when the subscriber cabling may be exposed to heavy transients and should always be used if there are outdoor cables. The ring voltage generator is needed when there are several phones in parallel on the same line, or the lines are very long.
AlphaCom E20/E26
Telephones and control outputs are connected to a connection board mounted on the exchange connection field.
Telephone connection board with transient protection (100 9930 202) and subscriber connection cable with filter board (100 9501 031) must be purchased separately.
AlphaCom E7
All telephones are connected by means of pluggable screw terminals on the exchange back-plane.
Note: When the ATLB board is used in AlphaCom E7 only four RCO's are available.
Installation Overview