Actions

Difference between revisions of "Relay Settings (Edge)"

From Zenitel Wiki

(Operating the relay of a Remote Device)
Line 7: Line 7:
 
If there is a need to change the Relay operation, this is done at the Edge Controller, which will push configuration to the actual station. There is no need to log on to each individual station.
 
If there is a need to change the Relay operation, this is done at the Edge Controller, which will push configuration to the actual station. There is no need to log on to each individual station.
  
 +
== Local relay ==
 
'''Configuration of relay''':
 
'''Configuration of relay''':
* [[Logging into an IP Station|Log on to the Edge Controller]], and select '''Edge Controller''' > '''System Configuration''' > '''Special Settings'''
+
 
* Under the '''Relay''' column, select '''Show/Hide Settings''' for the station on which you want to configure the relay
+
*[[Logging into an IP Station|Log on to the Edge Controller]], and select '''Edge Controller''' > '''System Configuration''' > '''Special Settings'''
 +
*Under the '''Relay''' column, select '''Show/Hide Settings''' for the station on which you want to configure the relay
  
 
[[File:Edge Relays.png|thumb|left|700px|Relay configuration]]
 
[[File:Edge Relays.png|thumb|left|700px|Relay configuration]]
Line 16: Line 18:
 
   
 
   
 
'''Choose Relay to Configure''':
 
'''Choose Relay to Configure''':
* Depending on the station/device model, it might have one or more relays. In the '''Choose Relay to Configure''' dropdown, you select which of the relays you want to configure. One can also [[#Operating the relay of a Remote Device|operate a relay on a Remote Device]].  
+
 
 +
*Depending on the station/device model, it might have one or more relays. In the '''Choose Relay to Configure''' dropdown, you select which of the relays you want to configure. One can also [[#Operating the relay of a Remote Device|operate a relay on a Remote Device]].
  
 
There are 4 different states: on, off, slow blinking and fast blinking. The relay state can change either with a remote digit (DTMF signal) ''during a call'', or if the station state changes.
 
There are 4 different states: on, off, slow blinking and fast blinking. The relay state can change either with a remote digit (DTMF signal) ''during a call'', or if the station state changes.
  
 
'''Remote DTMF digit during call''':
 
'''Remote DTMF digit during call''':
 +
 
*'''Remote Digit For Relay On/Off/Slow flash/Fast flash:''' Change the relay to on/off/Slow flash/Fast flash state when the specified remote DTMF digit is received
 
*'''Remote Digit For Relay On/Off/Slow flash/Fast flash:''' Change the relay to on/off/Slow flash/Fast flash state when the specified remote DTMF digit is received
 
*'''Remote Digit For Relay Toggle:''' Toggles the relay on/off every time the specified DTMF digit is received
 
*'''Remote Digit For Relay Toggle:''' Toggles the relay on/off every time the specified DTMF digit is received
Line 26: Line 30:
  
 
'''Change of station state''':
 
'''Change of station state''':
 +
 
*'''Outgoing Ringing / Incoming Ringing''': Operate the relay while the station is ringing due to an incoming or outgoing call. The ringing state lasts until the call has been answered, or the ringing times out.
 
*'''Outgoing Ringing / Incoming Ringing''': Operate the relay while the station is ringing due to an incoming or outgoing call. The ringing state lasts until the call has been answered, or the ringing times out.
* '''Outgoing Call / Incoming Call''': Operate the relay while the station is in conversation.  The call state occurs from the call is accepted until the call ends.
+
*'''Outgoing Call / Incoming Call''': Operate the relay while the station is in conversation.  The call state occurs from the call is accepted until the call ends.
* '''Group Call''': Operate the relay when the station receives a group call
+
*'''Group Call''': Operate the relay when the station receives a group call
* '''Idle''': Choose which state the relay should change to when the station is in idle (no active calls).
+
*'''Idle''': Choose which state the relay should change to when the station is in idle (no active calls).
* '''Error''': Choose which state the relay should change to when the station is off-line (not registered to the Edge Controller).
+
*'''Error''': Choose which state the relay should change to when the station is off-line (not registered to the Edge Controller).
  
== Operating the relay of a Remote Device ==
+
==Operating the relay of a Remote Device==
 
[[File:Edge RemoteRelayExample.PNG|thumb|right|400px|Controlling Remote Relay unit in safe area]]
 
[[File:Edge RemoteRelayExample.PNG|thumb|right|400px|Controlling Remote Relay unit in safe area]]
 
For security reasons it might not be desired to use the relay of the door intercom itself, but instead control the relay of a remote relay unit located in a safe area.
 
For security reasons it might not be desired to use the relay of the door intercom itself, but instead control the relay of a remote relay unit located in a safe area.
  
 
Typical remote relay units can be:
 
Typical remote relay units can be:
* [[TKIS-2]] (one relay)
+
 
* [[TKIE-2]] (two relays)
+
*[[TKIS-2]] (one relay)
* [[TKIE-2]] + [[TA-10]] (four relays)
+
*[[TKIE-2]] (two relays)
* [[IP-LCM|IP-LCM unit]] (eight relays)
+
*[[TKIE-2]] + [[TA-10]] (four relays)
 +
*[[IP-LCM|IP-LCM unit]] (eight relays)
  
 
{{note|Only physical relays can be controlled, the 6 GPIO's on Turbine devices cannot be controlled using this feature}}
 
{{note|Only physical relays can be controlled, the 6 GPIO's on Turbine devices cannot be controlled using this feature}}
Line 46: Line 52:
 
<div style="float:right;"> <youtube width="300" height="180">iNom-YhkheM=3s</youtube>  </div>
 
<div style="float:right;"> <youtube width="300" height="180">iNom-YhkheM=3s</youtube>  </div>
 
'''Configuration of remote relay''':
 
'''Configuration of remote relay''':
* [[Logging into an IP Station|Log on to the Edge Controller]], and select '''Edge Controller''' > '''System Configuration''' > '''Special Settings'''
+
 
* Under the '''Relay''' column, select '''Show/Hide Settings''' for the ''door intercom''
+
*[[Logging into an IP Station|Log on to the Edge Controller]], and select '''Edge Controller''' > '''System Configuration''' > '''Special Settings'''
* In the '''Choose Relay to Configure''' dropdown, select '''Remote Device'''.  
+
*Under the '''Relay''' column, select '''Show/Hide Settings''' for the ''door intercom''
 +
*In the '''Choose Relay to Configure''' dropdown, select '''Remote Device'''.
  
 
Enter Remote Device Settings:  
 
Enter Remote Device Settings:  
* The IP Address of Remote Device
+
 
* Which relay to use
+
*The IP Address of Remote Device
* Pulse time of the relay in seconds
+
*Which relay to use
* Which digit to trigger the relay
+
*Pulse time of the relay in seconds
 +
*Which digit to trigger the relay
  
 
[[File:Edge RemoteRelayConfig.PNG|thumb|left|700px|Pressing digit "6" while in communication with door station 12, will operate relay 1 of the remote device 10.9.8.132 for 3 seconds.]]
 
[[File:Edge RemoteRelayConfig.PNG|thumb|left|700px|Pressing digit "6" while in communication with door station 12, will operate relay 1 of the remote device 10.9.8.132 for 3 seconds.]]
 
<br style="clear:both;" />
 
<br style="clear:both;" />
 
 
 
  
 
[[Category: IC-EDGE Configuration]]
 
[[Category: IC-EDGE Configuration]]
 
[[Category:IC-EDGE Integrations]]
 
[[Category:IC-EDGE Integrations]]

Revision as of 01:02, 11 December 2023

Edge-icon.jpg

This article describes how to configure the Relays of stations used in an IC-EDGE System.

By default the relay is preconfigured to generate a 3 second pulse when the station receives "DTMF" digit "6" during an established call (Door Opening feature).

If there is a need to change the Relay operation, this is done at the Edge Controller, which will push configuration to the actual station. There is no need to log on to each individual station.

Local relay

Configuration of relay:

  • Log on to the Edge Controller, and select Edge Controller > System Configuration > Special Settings
  • Under the Relay column, select Show/Hide Settings for the station on which you want to configure the relay
Relay configuration



Choose Relay to Configure:

  • Depending on the station/device model, it might have one or more relays. In the Choose Relay to Configure dropdown, you select which of the relays you want to configure. One can also operate a relay on a Remote Device.

There are 4 different states: on, off, slow blinking and fast blinking. The relay state can change either with a remote digit (DTMF signal) during a call, or if the station state changes.

Remote DTMF digit during call:

  • Remote Digit For Relay On/Off/Slow flash/Fast flash: Change the relay to on/off/Slow flash/Fast flash state when the specified remote DTMF digit is received
  • Remote Digit For Relay Toggle: Toggles the relay on/off every time the specified DTMF digit is received
  • Remote Digit For Relay Timed Relay On: Choose which remote digit (DTMF signal) should pulse the relay for the number of seconds specified in Timed Relay Duration. This state is normally used for Door Opening feature.

Change of station state:

  • Outgoing Ringing / Incoming Ringing: Operate the relay while the station is ringing due to an incoming or outgoing call. The ringing state lasts until the call has been answered, or the ringing times out.
  • Outgoing Call / Incoming Call: Operate the relay while the station is in conversation. The call state occurs from the call is accepted until the call ends.
  • Group Call: Operate the relay when the station receives a group call
  • Idle: Choose which state the relay should change to when the station is in idle (no active calls).
  • Error: Choose which state the relay should change to when the station is off-line (not registered to the Edge Controller).

Operating the relay of a Remote Device

Controlling Remote Relay unit in safe area

For security reasons it might not be desired to use the relay of the door intercom itself, but instead control the relay of a remote relay unit located in a safe area.

Typical remote relay units can be:

Note icon Only physical relays can be controlled, the 6 GPIO's on Turbine devices cannot be controlled using this feature


Configuration of remote relay:

  • Log on to the Edge Controller, and select Edge Controller > System Configuration > Special Settings
  • Under the Relay column, select Show/Hide Settings for the door intercom
  • In the Choose Relay to Configure dropdown, select Remote Device.

Enter Remote Device Settings:

  • The IP Address of Remote Device
  • Which relay to use
  • Pulse time of the relay in seconds
  • Which digit to trigger the relay
Pressing digit "6" while in communication with door station 12, will operate relay 1 of the remote device 10.9.8.132 for 3 seconds.