Search results
Create the page "Event Handler applications" on this wiki! See also the search results found.
- ...f these applications is the intercom (AMCd) application. Examples of other applications are [[SIP]], [[Syslog (AlphaCom)|Syslog]], [[AlphaWeb]] (web server) and [[ * Reboot the exchange. This will restart the Linux operative system and all applications. A reboot takes approx. xx seconds in a fully equipped E7, and xx seconds i2 KB (344 words) - 11:22, 8 September 2017
- ...nge, designed to provide critical communications and serve a wide range of applications. <br /> * [[Event Handler]]1 KB (155 words) - 13:31, 15 August 2017
- ==== Event Handler programming ==== The conference is started by dialing event trigger 9533 from the Bridge. UDD 500, which contains the current Active Us5 KB (837 words) - 14:35, 31 May 2022
- *Control room applications: No need for an additional intercom device at the desk. Use the computers a ...e to listen to any of these services, add the following event to the Event Handler:3 KB (378 words) - 08:19, 5 April 2024
- ...t box, and select the button '''Events'''. Press '''Insert''' to create an event with the following parameters (here RCO 1 is used as an example): [[File:Application_A3a.png|500px|left|thumb|Event for operating the RCO]]3 KB (428 words) - 11:01, 1 June 2022
- The '''Free Seating''' system runs on standard [[AMC]] SW using the [[Event Handler]] and the [[AlphaPro]] WACS module for swapping two users. The [[Event Handler]] is used to activate and send [[AlphaNet Data Protocol]] data messages to8 KB (1,173 words) - 11:31, 1 June 2022
- ==Creating Event for Door Opening == ...list to the left. Then select the button '''Events'''. '''Insert''' a new event with the following properties:7 KB (1,107 words) - 11:16, 24 October 2023
- * DAK1 = Leave blank in the DAK table (key press is triggering event 30) * DAK2 = Leave blank in the DAK table (key press is triggering event 30)9 KB (1,426 words) - 17:54, 2 February 2023
- The built-in [[Scheduler (Event Type)|Scheduler]] function in [[:category:ICX-AlphaCom Platform|ICX-AlphaCo Typical applications:5 KB (712 words) - 20:36, 22 July 2022
- * In order to make the [[Event Handler]] programming very general the [[AGA]] ports should be assigned directory n === Event Handler programming ===7 KB (1,079 words) - 11:13, 8 July 2022
- The Delayed Call functionality is controlled by the [[Event Handler]], which is configured from [[AlphaPro]]. '''Event 1''' - When the ID+M (= subevent 2) call button is pressed (= ON), start a3 KB (533 words) - 10:39, 1 June 2022
- ...select the CRM IV in the list box, and press '''Events'''. '''Insert''' an event as described below. |width="100pt"|'''Event Owner''':5 KB (699 words) - 14:39, 14 June 2018
- .... The relay in the interface is controlled by the RCO command in the event handler. The relay outputs of the interface needs to be mapped to a logical RCO. ...stbox, and select the button '''Events'''. Press '''Insert''' to create an event with the following parameters (here RCO 1 is used as an example):6 KB (869 words) - 11:26, 24 May 2023
- Configure the Alarm Button to dial event trigger number 9534 (feature 52). The number 9534 is included in a default == Event Handler configuration ==12 KB (1,938 words) - 17:11, 4 January 2023
- Due to the Event Handler configuration used in this application, a strict number plan must be follow *The "Call setup", "Listen-In" and "Record" are Event Triggers, feature 52.11 KB (1,810 words) - 11:53, 10 February 2023
- ...forwarded to a dummy station, which will queue the call and via the event handler send the SMS message. If there are several simultaneous call requests, a SM ...current mail is deleted ($CANM). If there are more calls in the queue, the event "New current mail" will be re-triggered, causing a new SMS to be sent. This13 KB (1,988 words) - 12:08, 23 February 2023
- * The number of an event trigger ...mming can be used to solve such applications ([[Event Trigger (Event Type)|Event Trigger Feature]]).13 KB (1,131 words) - 08:12, 22 September 2022
- ...d off by an [[RCO - Set Remote Control Output|RCO command]] in the [[Event Handler]]. ...tory number in the list box, and press the button 'Events'. 'Insert' a new event with the following attributes:15 KB (2,245 words) - 13:44, 5 July 2022
- The application is suitable not only for elevators, but also for other applications, such as: == About the Event Handler programming ==15 KB (2,374 words) - 12:09, 24 February 2023
- * Event handler %1.NAM [[Category:ICX-AlphaCom Applications]]4 KB (606 words) - 12:59, 24 May 2022