Actions

Difference between revisions of "Door Opening using Dummy Number (Event Handler)"

From Zenitel Wiki
Line 1: Line 1:
−
===Situation===
+
==Situation==
−
Some gates are not equipped with door stations, but the operator should use the same [[Door opening]] procedure to open the door. When the operator gets a signal that there is someone at the door he should dial a dummy number, then press digit 6 to operate a relay output (i.e. a [[RCO]]).
+
Some gates are not equipped with door stations, but the operator should use the same [[Door opening]] procedure to open the door. When the operator gets a signal that there is someone at the door he should dial a 'dummy' number, then press digit 6 to operate a relay output (i.e. a [[RCO]]).
  
−
=== Solution===
+
==Solution==
−
In the example below any station can dial 9545 + 6 to trigger RCO 4 for 2 seconds, and disconnect with success-tone.
+
In the example below any station can dial 9545 + 6 to trigger [[RCO]] 4 for 2 seconds, and disconnect with success-tone.
 +
Use the two-step event trigger, [[Event trigg on dialing digits|feature 105]].
  
−
Use the two-step event trigger, [[Event trigg on dialing digits|feature 105]]. In AlphaPro, Directory & Features, create a directory number, feature 105, for each door. Directory number 9545 is included by default.
 
  
−
In '''Exchange & System''' -> '''Events''', create a new event:
+
==Programming==
  
 +
In [[AlphaPro]], [[Directory_%26_Features_%28AlphaPro%29|Directory & Features]], press "Insert" to create a directory number, feature 105, for each door. Directory number 9545 is included by default.
 +
In [[AlphaPro]], go to [[Exchange_%26_System_%28AlphaPro%29#Events|Exchange and System -> Events]], press Insert and create the following event:
 +
------------
 
[[Image:Event 25 Event trigger w Parameter.jpg|thumb|right|Event Handler configuration]]
 
[[Image:Event 25 Event trigger w Parameter.jpg|thumb|right|Event Handler configuration]]
 
{|  
 
{|  
 
|-
 
|-
 
|width="100pt"|'''Event Owner''':
 
|width="100pt"|'''Event Owner''':
−
|width="300pt"|The operator station or an [[UDP]] group
+
|width="400pt"|The operator station or a [[UDP]] group
 
|-
 
|-
−
|'''Event type''': || 25 – Event Trigger w/User Parameter
+
|'''Event type''': || [[Event Trigger with parameter|25 – Event Trigger w/User Parameter]]
 
|-
 
|-
 
|'''Subevent''': || 6
 
|'''Subevent''': || 6
Line 21: Line 24:
 
|'''When change to''': || ON
 
|'''When change to''': || ON
 
|-
 
|-
−
|'''When related to''': || Directory number: 9545
+
|'''When related to''': || Directory number, Id: 9545
 
|-
 
|-
−
|'''Action:''' || RCO 4 ON 20
+
|'''Action:''' || [[RCO]] 4 ON 20
 
|-
 
|-
−
|  || $DISCON_ST L%1.dir U2
+
|  || [[DISCON_ST|$DISCON_ST]] L%1.dir U2
 
|-
 
|-
 
|}
 
|}
 
<br><br>
 
<br><br>
  
−
===Explanation ===
+
------------
−
* Subevent 6: digit 6
+
===Explanation===
−
* When Change to ON: When the digit is pressed (not released)
+
Subevent 6: digit 6
−
* RCO 6 ON 20: Pulse RCO 6 for 2,0 seconds
+
When Change to ON: When the digit is pressed (not released)
−
* $[[DISCON_ST]] L%1.dir U2: Disconnect the station with successtone
+
RCO 6 ON 20: Pulse RCO 6 for 2,0 seconds
 +
$[[DISCON_ST]] L%1.dir U2: Disconnect the station with successtone

Revision as of 13:05, 20 November 2008

Situation

Some gates are not equipped with door stations, but the operator should use the same Door opening procedure to open the door. When the operator gets a signal that there is someone at the door he should dial a 'dummy' number, then press digit 6 to operate a relay output (i.e. a RCO).

Solution

In the example below any station can dial 9545 + 6 to trigger RCO 4 for 2 seconds, and disconnect with success-tone. Use the two-step event trigger, feature 105.


Programming

In AlphaPro, Directory & Features, press "Insert" to create a directory number, feature 105, for each door. Directory number 9545 is included by default. In AlphaPro, go to Exchange and System -> Events, press Insert and create the following event:

Event Handler configuration
Event Owner: The operator station or a UDP group
Event type: 25 – Event Trigger w/User Parameter
Subevent: 6
When change to: ON
When related to: Directory number, Id: 9545
Action: RCO 4 ON 20
  $DISCON_ST L%1.dir U2



Explanation

Subevent 6: digit 6
When Change to ON: When the digit is pressed (not released)
RCO 6 ON 20: Pulse RCO 6 for 2,0 seconds
$DISCON_ST L%1.dir U2: Disconnect the station with successtone
Retrieved from "https://wiki.zenitel.com/w/index.php?title=Door_Opening_using_Dummy_Number_(Event_Handler)&oldid=60016"