Actions

Difference between revisions of "IND - Indicator control for CRMIV LEDs, buzzer etc."

From Zenitel Wiki

(→‎Syntax)
 
(119 intermediate revisions by 7 users not shown)
Line 1: Line 1:
−
== Syntax ==
+
{{AI}}
 +
The IND (INDication) or GIND action are used in the [[Event Handler]] for sending commands to a station or a group of stations. The following stations are supporting the IND command:
  
−
IND  <phys.no>  <key.no>  <led.no/buzzer>  <ind-type>  [ON/OFF]
+
*[[IP Flush Master - 1008031000|IP Flush Master and CRM V]]: Control the LED's in the DAK keys
 +
*[[Control Room Master IV|CRM IV]]: Control the LED's in the DAK keys, the internal buzzer or relay, and the backlight of the display
 +
*[[Dual Display Station - 1007007000|DualDisplay station]]: Control the video-state of the DAK-display
 +
*[[Tamper and Vandal Proof Station - 1007063000|Priscom station]]: Control the outputs used for lamps, cell light, call LED and spare output
 +
*[[IP-ARIO]]: Control the Error LED and the Radio LED
 +
*IP Substation: Control relay and spare output
 +
*Turbine station: Control relay and the 6 additional outputs
 +
*[[ECPIR-3P]] and [[EBMDR-8]] module
  
 +
{{note|Note: Using the IND command also triggers a ST_STATE message on the OPC port; it is advisable to add two (or possibly more, depending on the system load) PAUSE commands before the IND command, especially when the event trigger is event 7, 8 or 44, When Change To OFF}}
  
−
'''phys.no''':
+
==Command syntax==
−
:*1-552 = The physical number of the station
+
'''IND command:'''
 +
{{code|IND <station phys.no> <output> <LED no/buzzer> <Ind-type> [state]}}
 +
Example: On station 2, key 23, turn green led, fast flashing, ON
 +
{{code|IND  2  23  2  3  ON}}
  
−
'''key.no''':
+
'''GIND command:'''
−
:*1-100 = The key number of the DAK-key <br>
+
{{code|GIND <group ind> <output> <LED no/buzzer> <Ind-type> [state] }}
−
:*1023 = Buzzer
 
−
:*1024 = Display
 
  
−
'''led.no/buzzer''': <br>
+
:<group ind> is the AlphaCom group index number 1-250. (Not the group directory number)
−
:If the previous parameter was DAK-key (1 - 100):
 
−
:*1 = Red LED
 
−
:*2 = Green LED
 
  
−
:If the previous parameter was Buzzer (1023):
+
There must be a space between the command parameters.
−
:*1 = Internal buzzer
 
−
:*2 = External buzzer (relay)
 
  
−
:If the previous parameter was Display (1024):
+
Parameter description:
−
:*1 = Backlight
 
  
−
'''ind-type''':
+
{| border="1"
−
:LEDs and display:
+
! style="background:#ffdead;" width="180" |Station/Parameter
−
:*1 = continuous (low priority)  
+
! style="background:#ffdead;" width="100" |phys. number
−
:*2 = slow flash (medium priority)  
+
! style="background:#ffdead;" width="250" |output
−
:*3 = fast flash (high priority)  
+
! style="background:#ffdead;" width="250" |LED no/buzzer
 +
! style="background:#ffdead;" width="300" |IND-type
 +
! style="background:#ffdead;" width="80" |[state]
 +
|-
 +
| valign="top" align="center" |'''CRM V and IP Flush Master (8024)'''
 +
| valign="top" align="center" |1 - 552
 +
| valign="top" |1-100 = DAK-key number
 +
| valign="top" |1 = Red LED  <br>
 +
2 = Green LED  <br>
 +
| valign="top" |1 = continuous (low priority) <br>
 +
2 = slow flash (medium priority) <br>
 +
3 = fast flash (high priority) <br>
 +
| valign="top" |ON or OFF
 +
|-
 +
| valign="top" align="center" |'''IP Substation (8022)'''
 +
| valign="top" align="center" |1 - 552
 +
| valign="top" |1 = Relay <br> 2 = Spare output
 +
| valign="top" |Always "1"<br>
 +
| valign="top" |1 = continuous (low priority) <br>
 +
2 = slow flash (medium priority) <br>
 +
3 = fast flash (high priority) <br>
 +
| valign="top" |ON or OFF
 +
|-
 +
| valign="top" align="center" |'''Turbine device'''
 +
| valign="top" align="center" |1 - 552
 +
| valign="top" |11-16 = Outputs<br> 17 = Relay <br> 18 = Relay 2 (Turbine Extended) <br> ''See note below!''
 +
| valign="top" |Always "1"<br>
 +
| valign="top" |1 = continuous (low priority) <br>
 +
2 = slow flash (medium priority) <br>
 +
3 = fast flash (high priority) <br>
 +
| valign="top" |ON or OFF
 +
|-
 +
| valign="top" align="center" |'''IP-LCM'''
 +
| valign="top" align="center" |1 - 552
 +
| valign="top" |17 = Relay <br> 11-16 = Spare outputs <br> 27-34 = external relays <br> ''See note below!''
 +
| valign="top" |Always "1"<br>
 +
| valign="top" |1 = continuous (low priority) <br>
 +
2 = slow flash (medium priority) <br>
 +
3 = fast flash (high priority) <br>
 +
| valign="top" |ON or OFF
 +
|-
 +
| valign="top" align="center" |'''ECPIR-3P'''
 +
| valign="top" align="center" |1 - 552
 +
| valign="top" |1-100 = DAK-key number
  
−
:Buzzers:
 
−
:*1 = 1 bleep per 8 seconds (low priority)
 
−
:*2 = 1 bleep per 2 seconds (medium priority)
 
−
:*3 = 4 bleeps per second (high priority)
 
−
:*4 = continuous (alarm priority)
 
  
  
−
'''[state] OFF or ON''':(capital letters)
 
−
:The brackets [ ] indicate that this command is optional. If nothing is entered in this field, the indication is switched on/off along with the event. By entering OFF, for example, you can set an indication to turn off when the event
 
−
turns on.
 
  
−
== Example ==
+
513 = Fault LED<br> ''Requires AMC 13.1.x.x''
 +
| valign="top" |1 = Red LED  <br>2 = Green LED
  
−
  IND 2  23 2  3 ON – Station 2, key 23, turn green led, fast flashing, ON
+
 
 +
 
 +
Always "1"<br>
 +
| valign="top" |1 = continuous (low priority) <br>
 +
2 = slow flash (medium priority) <br>
 +
3 = fast flash (high priority) <br>
 +
| valign="top" |ON or OFF
 +
|-
 +
| valign="top" align="center" |'''DualDisplay'''
 +
| valign="top" align="center" |1 - 552
 +
| valign="top" |1-100 = The DAK-key line
 +
| valign="top" |Always "1"
 +
| valign="top" |Video-state of the DAK-display: <br>
 +
 
 +
:0 = Normal <br>
 +
:1 = Inverse <br>
 +
:2 = Slow flash <br>
 +
:3 = Fast flash <br>
 +
| valign="top" |ON or OFF
 +
|-
 +
| valign="top" align="center" |'''IP-ARIO'''
 +
| valign="top" align="center" |1 - 552
 +
| valign="top" |1 = Radio LED <br> 2 = Error LED
 +
| valign="top" |1 = Red LED  (Radio and Error) <br>
 +
2 = Green LED (Radio LED only)<br>
 +
| valign="top" |1 = continuous (low priority) <br>
 +
2 = slow flash (medium priority) <br>
 +
3 = fast flash (high priority) <br>
 +
| valign="top" |ON or OFF
 +
|-
 +
| valign="top" align="center" |'''PrisCom'''
 +
| valign="top" align="center" |1 - 552
 +
| valign="top" |1 - 4 = Lamp outputs <br> 5 - 6 = Spare outputs <br> 7 = Relay (Cell light) <br> 8 = Call LED
 +
| valign="top" |Always "1"
 +
| valign="top" |1 = continuous (low priority) <br>
 +
2 = slow flash (medium priority) <br>
 +
3 = fast flash (high priority) <br>
 +
| valign="top" |ON or OFF
 +
|-
 +
| valign="top" align="center" |'''CRM IV'''
 +
| valign="top" align="center" |1 - 552
 +
| valign="top" |1-100 = DAK-key number<br> 1023 = Buzzer <br> 1024 = Display backlight<br>
 +
| valign="top" |DAK-key: <br>
 +
 
 +
:1 = Red LED <br>
 +
:2 = Green LED  <br>
 +
 
 +
Buzzer: <br>
 +
 
 +
:1 = Internal buzzer <br>
 +
:2 = External buzzer (relay)  <br>
 +
 
 +
Display backlight: <br>
 +
 
 +
:1 = Backlight
 +
| valign="top" |DAK LED's: <br>
 +
 
 +
:1 = continuous (low priority) <br>
 +
:2 = slow flash (medium priority) <br>
 +
:3 = fast flash (high priority) <br>
 +
 
 +
Buzzers: <br>
 +
 
 +
:1 = 1 bleep per 8 seconds (low priority) <br>
 +
:2 = 1 bleep per 2 seconds (medium priority) <br>
 +
:3 = 4 bleeps per second (high priority) <br>
 +
:4 = continuous (alarm priority)
 +
 
 +
Display backlight: <br>
 +
 
 +
:1 = continuous
 +
| valign="top" |ON or OFF
 +
|-
 +
|}
 +
 
 +
The ''state'' parameter is optional. If nothing is entered in this field, the indication is switched on/off along with the event. By entering OFF, for example, you can set an indication to turn off when the event turns on.
 +
 
 +
{{Note| '''Note on Turbine''': The output numbers depend on the AMC software version.
 +
* ''AMC version 11.2.3.9 and earlier: Use IND numbers 1 - 7''
 +
* ''AMC version 11.2.3.10: Outputs cannot be controlled by IND command''
 +
* ''AMC version 11.2.3.11 and later: Use IND numbers 11 - 17'' }}
 +
 
 +
==Related articles==
 +
 
 +
*[[Control_Room_Master_IV#Configuration|CRM IV: LED and buzzer control]]
 +
*[[CRM: Indicate status of remote stations in AlphaNet]]
 +
*[[RCO - Remote Control Output]]
 +
*[[SET_IPRCO|$SET_IPRCO]]: This data command can be used to activate Remote Control Outputs on IP Stations and IPARIO without having to define the RCO's in the RCO table.
  
 
[[Category:Event Handler]]
 
[[Category:Event Handler]]
 +
[[Category:Built-In Action Commands]]

Latest revision as of 10:44, 22 December 2022

AI.png

The IND (INDication) or GIND action are used in the Event Handler for sending commands to a station or a group of stations. The following stations are supporting the IND command:

  • IP Flush Master and CRM V: Control the LED's in the DAK keys
  • CRM IV: Control the LED's in the DAK keys, the internal buzzer or relay, and the backlight of the display
  • DualDisplay station: Control the video-state of the DAK-display
  • Priscom station: Control the outputs used for lamps, cell light, call LED and spare output
  • IP-ARIO: Control the Error LED and the Radio LED
  • IP Substation: Control relay and spare output
  • Turbine station: Control relay and the 6 additional outputs
  • ECPIR-3P and EBMDR-8 module
Note icon Note: Using the IND command also triggers a ST_STATE message on the OPC port; it is advisable to add two (or possibly more, depending on the system load) PAUSE commands before the IND command, especially when the event trigger is event 7, 8 or 44, When Change To OFF


Command syntax

IND command:

IND <station phys.no> <output> <LED no/buzzer> <Ind-type> [state]


Example: On station 2, key 23, turn green led, fast flashing, ON

IND 2 23 2 3 ON


GIND command:

GIND <group ind> <output> <LED no/buzzer> <Ind-type> [state]


<group ind> is the AlphaCom group index number 1-250. (Not the group directory number)

There must be a space between the command parameters.

Parameter description:

Station/Parameter phys. number output LED no/buzzer IND-type [state]
CRM V and IP Flush Master (8024) 1 - 552 1-100 = DAK-key number 1 = Red LED

2 = Green LED

1 = continuous (low priority)

2 = slow flash (medium priority)
3 = fast flash (high priority)

ON or OFF
IP Substation (8022) 1 - 552 1 = Relay
2 = Spare output 		Always "1"
 1 = continuous (low priority)

2 = slow flash (medium priority)
3 = fast flash (high priority)

ON or OFF
Turbine device 1 - 552 11-16 = Outputs
17 = Relay
18 = Relay 2 (Turbine Extended)
See note below! 		Always "1"
 1 = continuous (low priority)

2 = slow flash (medium priority)
3 = fast flash (high priority)

ON or OFF
IP-LCM 1 - 552 17 = Relay
11-16 = Spare outputs
27-34 = external relays
See note below! 		Always "1"
 1 = continuous (low priority)

2 = slow flash (medium priority)
3 = fast flash (high priority)

ON or OFF
ECPIR-3P 1 - 552 1-100 = DAK-key number



513 = Fault LED
Requires AMC 13.1.x.x

1 = Red LED
2 = Green LED


Always "1"

 1 = continuous (low priority)

2 = slow flash (medium priority)
3 = fast flash (high priority)

ON or OFF
DualDisplay 1 - 552 1-100 = The DAK-key line Always "1" Video-state of the DAK-display:
0 = Normal
1 = Inverse
2 = Slow flash
3 = Fast flash
ON or OFF
IP-ARIO 1 - 552 1 = Radio LED
2 = Error LED 		1 = Red LED (Radio and Error)

2 = Green LED (Radio LED only)

 1 = continuous (low priority)

2 = slow flash (medium priority)
3 = fast flash (high priority)

ON or OFF
PrisCom 1 - 552 1 - 4 = Lamp outputs
5 - 6 = Spare outputs
7 = Relay (Cell light)
8 = Call LED 		Always "1" 1 = continuous (low priority)

2 = slow flash (medium priority)
3 = fast flash (high priority)

ON or OFF
CRM IV 1 - 552 1-100 = DAK-key number
1023 = Buzzer
1024 = Display backlight
 DAK-key:
1 = Red LED
2 = Green LED

Buzzer:

1 = Internal buzzer
2 = External buzzer (relay)

Display backlight:

1 = Backlight
 DAK LED's:
1 = continuous (low priority)
2 = slow flash (medium priority)
3 = fast flash (high priority)

Buzzers:

1 = 1 bleep per 8 seconds (low priority)
2 = 1 bleep per 2 seconds (medium priority)
3 = 4 bleeps per second (high priority)
4 = continuous (alarm priority)

Display backlight:

1 = continuous
 ON or OFF

The state parameter is optional. If nothing is entered in this field, the indication is switched on/off along with the event. By entering OFF, for example, you can set an indication to turn off when the event turns on.

Note icon Note on Turbine: The output numbers depend on the AMC software version.
  • AMC version 11.2.3.9 and earlier: Use IND numbers 1 - 7
  • AMC version 11.2.3.10: Outputs cannot be controlled by IND command
  • AMC version 11.2.3.11 and later: Use IND numbers 11 - 17


Related articles

Retrieved from "https://wiki.zenitel.com/w/index.php?title=IND_-_Indicator_control_for_CRMIV_LEDs,_buzzer_etc.&oldid=231432"