Difference between revisions of "Main Settings (IP Stations)"
From Zenitel Wiki
Line 1: | Line 1: | ||
− | {{ | + | {{AEIPS}} |
* [[Logging into an IP Station|Logging into the IP Station]] | * [[Logging into an IP Station|Logging into the IP Station]] | ||
* Click '''Station Main > Main Settings''' to access the page for configuring station mode and Network Settings. | * Click '''Station Main > Main Settings''' to access the page for configuring station mode and Network Settings. | ||
Line 5: | Line 5: | ||
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
− | '''Station Mode:''' Select one of the available modes: AlphaCom, Exigo, SIP, | + | '''Station Mode:''' Select one of the available modes: ICX-AlphaCom, Exigo, SIP, Edge and Edge Controller. |
'''Product Model And Accessory [Turbine only]:''' Depending on the type of Turbine hardware, there are different Product models and accessories to choose from. Find your model here: [[:Category:Stations#Turbine_stations|Turbine Station Models]] | '''Product Model And Accessory [Turbine only]:''' Depending on the type of Turbine hardware, there are different Product models and accessories to choose from. Find your model here: [[:Category:Stations#Turbine_stations|Turbine Station Models]] | ||
'''IP Settings:''' | '''IP Settings:''' | ||
+ | Choose your preferred internet protocol; IPv4 or IPv6 | ||
* '''DHCP''' – Select this option if the IP station shall receive IP Settings from a DHCP server. | * '''DHCP''' – Select this option if the IP station shall receive IP Settings from a DHCP server. | ||
* '''Static IP''' – Select this option if the IP station shall use a static IP address. Enter values for: | * '''Static IP''' – Select this option if the IP station shall use a static IP address. Enter values for: |
Revision as of 14:06, 23 November 2020
- Logging into the IP Station
- Click Station Main > Main Settings to access the page for configuring station mode and Network Settings.
Station Mode: Select one of the available modes: ICX-AlphaCom, Exigo, SIP, Edge and Edge Controller.
Product Model And Accessory [Turbine only]: Depending on the type of Turbine hardware, there are different Product models and accessories to choose from. Find your model here: Turbine Station Models
IP Settings: Choose your preferred internet protocol; IPv4 or IPv6
- DHCP – Select this option if the IP station shall receive IP Settings from a DHCP server.
- Static IP – Select this option if the IP station shall use a static IP address. Enter values for:
- - IP-address
- - Subnet-mask
- - Gateway
- - DNS Server 1 (option for network administration)
- - DNS Server 2 (option for network administration)
- - Hostname (option for network administration)
- Disable Reset to Factory default settings using frontboard and I/O [Turbine only]: If enabled, factory reset will only be possible from StationWeb. This is disabled by default.
- Read IP Address [Turbine only]: Check the Read IP Address box to enable an unregistered station to speak the IP address when the call button is pressed. "Read IP Address" is default enabled.
- Enable RSTP [Turbine only] (for Industrial & Ex stations): Check the Enable RSTP box to enable RSTP. RSTP is only required when using redundant networking
- Ethernet Speed 10 Mbits/s [Turbine only]: Enable in some rare cases where it is not convenient to use 100 MBit/s Ethernet speed. Default Ethernet speed is 100 Mbit/s unless switch is configured to 10 Mbit/s.
- Use Last IP On DHCP failure [INCA only]: If the station does not receive an IP Address from a DHCP server at startup, it will use the last IP address.
- IGMP Version [INCA only]: Select IGMPv2 or IGMPv3 for multicast group membership.
Click Save followed by Apply to apply the new configuration settings.