Difference between revisions of "Main Settings - Edge Controller"
From Zenitel Wiki
| (26 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
{{E}} | {{E}} | ||
| − | + | This article describes how to configure a Zenitel IP device to act as an '''[[Edge Controller]]'''. | |
| − | This article describes how to configure a | ||
| − | {{note|You can do all configuration of your devices from the | + | {{note| |
| − | * [[Logging into an IP Station|Logging on to the device you will use as the | + | * ''Most Zenitel IP devices can act as an Edge Controller, see [[Edge Controller|full list here]]'' |
| − | * Select '''Main''' > '''Main Settings''' to access the page for configuring | + | * ''You can do all configuration of your devices from the Edge Controller. There is no need to log on to each device'' |
| − | [[File:Edge | + | * ''The Edge Controller should use a Static IP Address, not obtain IP address from a DHCP server'' }} |
| + | |||
| + | * [[Logging into an IP Station|Logging on to the device you will use as the Edge Controller]] | ||
| + | * Select '''Main''' > '''Main Settings''' to access the page for configuring Mode of operation and Network Settings. | ||
| + | [[File:Edge MainSettings2.PNG|thumb|left|700px|Setting the Edge Controller]] | ||
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
| − | ''' | + | '''Mode:''' Select the mode ''Edge Controller'' |
| − | '''Product Model And Accessory | + | '''Product Model And Accessory:''' Depending on the type of Turbine hardware, there are different Product models and accessories to choose from. Find your model here: [[:Category:Stations#Turbine_stations|Turbine Station Models]] |
'''IP Settings:''' | '''IP Settings:''' | ||
| − | + | * '''Static IP''' – The Edge Controller must be assigned a Static IP address. Enter values for: | |
| − | * '''Static IP''' – | ||
** '''IP-address''' | ** '''IP-address''' | ||
** '''Subnet-mask''' | ** '''Subnet-mask''' | ||
| − | ** '''Gateway''' | + | ** '''Gateway''': The controller must have a valid Default Gateway address defined. |
| − | ** '''DNS Server 1''' (option for network administration) | + | *** If there is no gateway in the network, you can enter the same IP Address as the Static IP Address. A valid gateway address is important for the [[Group Call (Edge)|Group Call feature]]. |
| − | ** '''DNS Server 2''' (option for network administration) | + | ** '''DNS Server 1''': (option for network administration) |
| − | ** '''Hostname''' (option for network administration) | + | ** '''DNS Server 2''': (option for network administration) |
| + | ** '''Hostname''': (option for network administration) | ||
* '''Disable Reset to Factory default settings using frontboard and I/O :''' If enabled, factory reset will only be possible from StationWeb. This is disabled by default. | * '''Disable Reset to Factory default settings using frontboard and I/O :''' If enabled, factory reset will only be possible from StationWeb. This is disabled by default. | ||
| − | *'''Read IP Address | + | *'''Read IP Address:''' When enabled an unregistered station will speak its IP address when the call button is pressed. "Read IP Address" is default enabled. |
| − | *'''Enable RSTP | + | *'''Enable RSTP''' (for Industrial & Ex stations): Check the '''Enable RSTP''' box to enable Rapid Speanning Tree Protocol RSTP. RSTP is only required when using redundant networking |
| − | *'''Ethernet Speed 10 Mbits/s | + | *'''Ethernet Speed 10 Mbits/s''': Enable in some rare cases where it is not convenient to use 100 MBit/s Ethernet speed. Default Ethernet speed is 100 Mbit/s unless switch is configured to 10 Mbit/s. |
| + | *'''IGMP Version [Desktop v2, IP FlushMaster v2 and IP-CROR v2 only]:''' Select IGMPv2 or IGMPv3 for multicast group membership. | ||
Click '''Save''' to apply the new configuration settings. | Click '''Save''' to apply the new configuration settings. | ||
[[Category: IC-EDGE Configuration]] | [[Category: IC-EDGE Configuration]] | ||
Latest revision as of 13:14, 12 January 2024
This article describes how to configure a Zenitel IP device to act as an Edge Controller.
|
|
- Logging on to the device you will use as the Edge Controller
- Select Main > Main Settings to access the page for configuring Mode of operation and Network Settings.
Mode: Select the mode Edge Controller
Product Model And Accessory: Depending on the type of Turbine hardware, there are different Product models and accessories to choose from. Find your model here: Turbine Station Models
IP Settings:
- Static IP – The Edge Controller must be assigned a Static IP address. Enter values for:
- IP-address
- Subnet-mask
- Gateway: The controller must have a valid Default Gateway address defined.
- If there is no gateway in the network, you can enter the same IP Address as the Static IP Address. A valid gateway address is important for the Group Call feature.
- DNS Server 1: (option for network administration)
- DNS Server 2: (option for network administration)
- Hostname: (option for network administration)
- Disable Reset to Factory default settings using frontboard and I/O : If enabled, factory reset will only be possible from StationWeb. This is disabled by default.
- Read IP Address: When enabled an unregistered station will speak its IP address when the call button is pressed. "Read IP Address" is default enabled.
- Enable RSTP (for Industrial & Ex stations): Check the Enable RSTP box to enable Rapid Speanning Tree Protocol RSTP. RSTP is only required when using redundant networking
- Ethernet Speed 10 Mbits/s: Enable in some rare cases where it is not convenient to use 100 MBit/s Ethernet speed. Default Ethernet speed is 100 Mbit/s unless switch is configured to 10 Mbit/s.
- IGMP Version [Desktop v2, IP FlushMaster v2 and IP-CROR v2 only]: Select IGMPv2 or IGMPv3 for multicast group membership.
Click Save to apply the new configuration settings.