Difference between revisions of "Situations that require System Reset"
From Zenitel Wiki
| (31 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| − | A number of AlphaPro settings require that the system is reset or rebooted in order to make the change | + | A number of AlphaPro settings require that the system is reset or rebooted in order to make the change take effect. |
| − | There are two types of reset: | + | The [[AMC-IP]] card is using [[Linux]] as operative system (OS). A number of applications are running on top of Linux. One of these applications is the intercom (AMCd) application. Examples of other applications are [[SIP]], [[Syslog (AlphaCom)|Syslog]], [[AlphaWeb]] (web server) and [[RMD|RingMaster interface]]. |
| − | * Reset of the AMC application | + | === Types of reset === |
| − | * Reset | + | There are two types of reset available from AlphaPro and AlphaWeb: |
| − | + | * Reset of the AMC application. This will restart the intercom application only. An AMC reset takes approx. xx seconds in a fully equipped E7, and xx seconds in a fully equipped E26. | |
| − | + | ** From AlphaPro: Press the 'Reset' button in the [[Communicate (alphaPro)|AlphaPro Communication Window (WACS)]] | |
| + | ** From AlphaWeb: Press 'Small Reset' in the System Maintenance -> System Recovery menu | ||
| + | * Reboot the exchange. This will restart the Linux operative system and all applications. A reboot takes approx. xx seconds in a fully equipped E7, and xx seconds in a fully equipped E26. | ||
| + | ** From AlphaWeb: Press 'Reboot' in the System Maintenance -> System Recovery menu | ||
| + | ** Press the reset button on [[APC]] (E20 and E26) or on the power board (E7) | ||
| + | ** Recycle the power (switch power off, then on) | ||
| − | + | ===Situations that require AMC application reset=== | |
| − | * | + | * Adding a new IP station in [[Users_%26_Stations_%28AlphaPro%29#General|Users & Stations]] |
| + | * Change of volume setting of an analog station (Changing the volume of an IP station do not require reset) | ||
| + | * Enabling [[RCO]]. Reset is required when a RCO is changed from device 0 / pin 0. | ||
| + | * Adding a SIP node | ||
| + | * Adding a node in AlphaNet | ||
| + | * Adding a module in MultiModule (i.e. after having entered the IP Address of the slave module in Exchange & System > System) | ||
| + | ===Situations that require Linux reset=== | ||
| + | * | ||
| − | |||
| − | |||
| + | ===Situations that don't require reset or reboot, but where the change take effect after a short time=== | ||
| + | * Changing or adding a new directory number | ||
| + | * Event Handler programming. It may take up to 1 minute before the change takes effect. (The change will take effect immediately if the AMC application is reset) | ||
| − | + | [[Category:AMC Software]] | |
| − | |||
Latest revision as of 11:22, 8 September 2017
A number of AlphaPro settings require that the system is reset or rebooted in order to make the change take effect.
The AMC-IP card is using Linux as operative system (OS). A number of applications are running on top of Linux. One of these applications is the intercom (AMCd) application. Examples of other applications are SIP, Syslog, AlphaWeb (web server) and RingMaster interface.
Contents
Types of reset
There are two types of reset available from AlphaPro and AlphaWeb:
- Reset of the AMC application. This will restart the intercom application only. An AMC reset takes approx. xx seconds in a fully equipped E7, and xx seconds in a fully equipped E26.
- From AlphaPro: Press the 'Reset' button in the AlphaPro Communication Window (WACS)
- From AlphaWeb: Press 'Small Reset' in the System Maintenance -> System Recovery menu
- Reboot the exchange. This will restart the Linux operative system and all applications. A reboot takes approx. xx seconds in a fully equipped E7, and xx seconds in a fully equipped E26.
- From AlphaWeb: Press 'Reboot' in the System Maintenance -> System Recovery menu
- Press the reset button on APC (E20 and E26) or on the power board (E7)
- Recycle the power (switch power off, then on)
Situations that require AMC application reset
- Adding a new IP station in Users & Stations
- Change of volume setting of an analog station (Changing the volume of an IP station do not require reset)
- Enabling RCO. Reset is required when a RCO is changed from device 0 / pin 0.
- Adding a SIP node
- Adding a node in AlphaNet
- Adding a module in MultiModule (i.e. after having entered the IP Address of the slave module in Exchange & System > System)
Situations that require Linux reset
Situations that don't require reset or reboot, but where the change take effect after a short time
- Changing or adding a new directory number
- Event Handler programming. It may take up to 1 minute before the change takes effect. (The change will take effect immediately if the AMC application is reset)