Latest revision as of 10:28, 8 September 2023

Previous Release - VSF-Fortitude8 7.4 Release Notes
Next Release - VSF-Fortitude8 8.0 Release Notes

This document provides the release notes for VSF-Fortitude8 7.5 with incremental bug fix releases. The release notes for VSF-Fortitude8 7.5 describe new features, improvements and issues fixed after VSF-Fortitude8 7.4.3.0.

Release info

Name: VSF-Fortitude8
Description: VSF-Fortitude8 is a firmware for Turbine Plus Intercoms including the following devices: TCIV-2+, TCIV-3+, TCIV-5+, TCIV-6+, TKIV+ and TMIV-1+

The firmware is delivered in two different files:

vsff8-7.5.3.x - Used for standard in-field upgrades
vsff8-prod-7.5.3.x - Used in production- and recovery upgrades.

Version: 7.5.3.1
Date: 23.05.2023
Status: General Availability

VSF-FORTITUDE8 7.5.3.1

Improvements

MTN-4004 Added support for more complex passwords

Passwords can now be 32 characters long, numbers, letters and the following special characters are supported ?!@$*,.- The password must meet the following criteria:

Minimum length of 8 characters
At least three out of the following four requirements must be met:
- Contains at least one digit (0-9)
- Contains at least one uppercase letter (A-Z)
- Contains at least one lowercase letter (a-z)
- Contains at least one special character

MTN-3259 Added option to make device ringlists independent of Edge Controller ringlist updates

When ‘No updates from Edge Controller’ checkbox is enabled, the ringlist is managed locally in the station. Global ringlist configuration in the Edge Controller is then ignored.

Issues fixed

MTN-4167 Upgrade of IPDM-V2_P now possible

Hardware revision 2 of the IPDM-V2_P failed to upgrade. This is resolved, and you can now upgrade to 7.5.3.1 or newer versions. Note that it is not possible to downgrade to versions older than 7.5.3.1.

MTN-4148 Circle showing PTZ location is now visible again

In image settings for video devices, the circle showing PTZ location was not showing. this is now fixed.

MTN-4056 It's now possible to disable OPTIONS timeout in Edge mode

Added a text field to disable or change the timeout for SIP OPTIONS when in Edge mode. Setting the timeout to 0 disables it. This option is analog to the one provided in SIP mode.

MTN-4047 It’s now possible to use W as the second letter in a password

The issue was that with W as second letter in a password you could not get access to the video configuration page on the device web. This is now fixed.

MTN-4000 RTSP can now be enabled or disabled

RTSP stream can be manually enabled or disabled (it's enabled by default), when disabled all RTSP related settings get grayed out (disabled).

MTN-3941 Accepting and responding with correct payload type

When receiving a video call, the TCIV+ would respond 200 OK with a Payload type which was different from the Payload type actually used. This could sometimes cause video issues such as late or no video at all.

Known Issues

MTN-4121 Known issue: Asterisk discards alternative profiles

Default setting for ITSV-5 sends 3 types (BP & MP & HP). However, Asterisk discards all but the first profile it receives (HP in this case). Since only the "Baseline profile" is supported on the device the video doesn't load. A workaround to this issue is to select "Baseline profile" as the H.264 profile type on the ITSV-5.

The issue has been reported and documented here: https://issues.asterisk.org/jira/browse/ASTERISK-29182

@@ Line 1: / Line 1: @@
 * Previous Release - [[VSF-Fortitude8 7.4 Release Notes]]
+* Next Release - [[VSF-Fortitude8 8.0 Release Notes]]
-This document provides the release notes for VSF-Fortitude8 7.4 with incremental bug fix releases. The release notes for VSF-Fortitude8 7.4 describe new features, improvements and issues fixed after VSF-Fortitude8 7.3.3.1.
+This document provides the release notes for VSF-Fortitude8 7.5 with incremental bug fix releases. The release notes for VSF-Fortitude8 7.5 describe new features, improvements and issues fixed after VSF-Fortitude8 7.4.3.0.
 ==Release info==
@@ Line 10: / Line 10: @@
 The firmware is delivered in two different files:
-*vsff8-7.4.3.x - Used for standard in-field upgrades
+*vsff8-7.5.3.x - Used for standard in-field upgrades
-*vsff8-prod-7.4.3.x - Used in production- and recovery upgrades.
+*vsff8-prod-7.5.3.x - Used in production- and recovery upgrades.
-'''Version:''' 7.4.3.0<br>
+'''Version:''' 7.5.3.1<br>
-'''Date:''' 30.01.2023 <br>
+'''Date:''' 23.05.2023 <br>
 '''Status:''' General Availability<br>
-=VSF-FORTITUDE8 7.4.3.0=
+=VSF-FORTITUDE8 7.5.3.1=
-== New Features==
-===MTN-3847 Option to disable registration in SIP mode added===
-A new option, No-Reg, has been added for Registration Method in Account Settings which will prevent registration towards a server. Device can operate in peer to peer mode.
-<br>
 ==Improvements==
-===MTN-3867 Relay activation is now supported from NxWitness VMS===
+===MTN-4004 Added support for more complex passwords===
-Added support for <onvifDevice:RelayOutputToken> tag to handle NxWitness implementation.
+Passwords can now be 32 characters long, numbers, letters and the following special characters are supported ?!@$*,.-
+The password must meet the following criteria:
+* Minimum length of 8 characters
+* At least three out of the following four requirements must be met:
+** Contains at least one digit (0-9)
+**Contains at least one uppercase letter (A-Z)
+** Contains at least one lowercase letter (a-z)
+**Contains at least one special character
-===MTN-3434 SNMP traps are now sent only on registration change state.===
+===MTN-3259 Added option to make device ringlists independent of Edge Controller ringlist updates===
-For example a trap will be sent when the devices goes from registered to unregistered (or vice versa), it was previously sent after each registration interval even if there were no changes to the state.
+When ‘No updates from Edge Controller’ checkbox is enabled, the ringlist is managed locally in the station. Global ringlist configuration in the Edge Controller is then ignored.
 <br>
 ==Issues fixed==
-=== MTN-4008 Syncing is now properly mapped for Alphacom "Noise Reduction" configuration level 0 to 7===
+=== MTN-4167 Upgrade of IPDM-V2_P now possible===
-The new configuration "Moderate" was not mapped. New mapping:
+Hardware revision 2 of the IPDM-V2_P failed to upgrade. This is resolved, and you can now upgrade to 7.5.3.1 or newer versions. Note that it is not possible to downgrade to versions older than 7.5.3.1.
-*0: ANC Disabled
-*1,2: ANC Enabled with Low Suppression
-*3,4: ANC Enabled with Moderate Suppression
-*5,6: ANC Enabled with High Suppression
-*7: ANC Enabled with Very High Suppression
-=== MTN-3958 Changing VoIP port range adds 1000 ports to the start value===
-Max port number is 65535, if start value is higher than 64535, remaining ports are allocated.
-=== MTN-3952 Added support for disabling factory reset from call button or input===
+=== MTN-4148 Circle showing PTZ location is now visible again===
-If the checkbox is enabled it's not possible to factory reset the device via call button or input.
+In image settings for video devices, the circle showing PTZ location was not showing. this is now fixed.
-=== MTN-3951 Loudspeaker volume configuration now applied correctly after reboot===
+=== MTN-4056 It's now possible to disable OPTIONS timeout in Edge mode===
-The loudspeaker level after boot was always similar to configuration, about +4dB. A configuration change up and down was needed to get back to configured audio level. The audio level shall now be applied as configured after boot.
+Added a text field to disable or change the timeout for SIP OPTIONS when in Edge mode. Setting the timeout to 0 disables it. This option is analog to the one provided in SIP mode.
-=== MTN-3910 Uploaded certificates can now be deleted===
+=== MTN-4047 It’s now possible to use W as the second letter in a password===
-The deletion of certificates uploaded in the device web was previously not possible. This is now fixed.
+The issue was that with W as second letter in a password you could not get access to the video configuration page on the device web. This is now fixed.
-=== MTN-3906 Device now waits for the ONVIF subscription timer to run out before deleting subscription===
+=== MTN-4000 RTSP can now be enabled or disabled===
-Subscription timer for ONVIF messages was running out before the message timer. This is now fixed.
+RTSP stream can be manually enabled or disabled (it's enabled by default), when disabled all RTSP related settings get grayed out (disabled).
-=== MTN-3896 Factory reset audio parameters now affects only Audio Settings page===
+=== MTN-3941 Accepting and responding with correct payload type===
-Factory reset audio parameters doesn't affect VAD, Tone Test and DAVC settings, only settings which are configured on Audio Settings page.
+When receiving a video call, the TCIV+ would respond 200 OK with a Payload type which was different from the Payload type actually used. This could sometimes cause video issues such as late or no video at all.
 <br>
 ==Known Issues==
-=== SUN-476 HTTP MJPEG stream has color distortions when viewed in LenelS2 OnGuard===
+===MTN-4121 Known issue: Asterisk discards alternative profiles===
-HTTP MJPEG stream has color distortions when viewed in LenelS2 OnGuard, recommendation is to use RTSP H.264 for video integration instead.
+Default setting for ITSV-5 sends 3 types (BP & MP & HP). However, Asterisk discards all but the first profile it receives (HP in this case). Since only the "Baseline profile" is supported on the device the video doesn't load. A workaround to this issue is to select "Baseline profile" as the H.264 profile type on the ITSV-5.
-=== SUN-349 MJPEG stream shows green image in Avigilon===
+The issue has been reported and documented here: https://issues.asterisk.org/jira/browse/ASTERISK-29182
-MJPEG stream shows green image in Avigilon, recommendation is to use H.264 for video integration instead.

Difference between revisions of "VSF-Fortitude8 7.5 Release Notes"

From Zenitel Wiki