Actions

Cisco Webex

From Zenitel Wiki

Zenitel devices as Webex Calling endpoints

Introduction

Zenitel devices operating in SIP mode can be integrated with Cisco Webex Calling as third-party SIP endpoints. This enables door intercoms, help points, emergency stations, and video intercoms to become part of the organization's Webex communication platform.

When registered to Webex Calling, users can place and receive calls between Zenitel devices, Webex applications, Webex desk phones, hunt groups, and PSTN destinations. Selected Zenitel video devices can also provide video communication in supported call scenarios.

This article describes the requirements, supported functionality, and configuration steps required to register a Zenitel SIP device to Cisco Webex Calling.

Requirements

Firmware

  • Zenitel devices must run firmware version 9.6.3.0 or later.

Supported Devices

All current Zenitel SIP-capable devices are supported, with the exception of:

Note icon Each Zenitel device is added to a workspace as a Customer Managed Device and requires a Webex Calling license (Professional or Common Area). Basic "Call on Webex" functionality without Webex Calling is not supported for third-party SIP endpoints.


Supported Features and Call Scenarios

Feature / Scenario Supported? Notes / Limitations / Configuration Details
Calls between Zenitel devices Yes
Call from Zenitel Device to Webex Soft Client Yes
Call from Webex Soft Client to Zenitel Device Yes
External PSTN Call to/from Zenitel Device Yes Via Webex Calling PSTN gateways/routes.
Two-way Audio Yes Since Zenitel devices do not support the Opus codec, calls are negotiated using G.722 or G.711.

Webex Calling rejects SIP offers containing only G.729. G.711 must always be present.
One-way / Two-way Video Yes Supported on TCIV, TCIV+, ZDD and ITSV series. Requires SDP media direction attribute sendrecv.
Door Opening / Relay Control Yes RFC 2833 DTMF only (for example digit 6). SIP INFO is not supported.
Hunt Groups / Simultaneous Ringing Yes Auto Answer must be disabled on Zenitel devices participating in simultaneous ringing or hunt group configurations.
Call Forwarding / Transfer / Hold Partial Dependent on device capabilities and Webex Calling configuration.
Direct SIP URI Dialing No Dialing SIP URIs directly (for example user@domain.rooms.webex.com) is not supported.
IPv6 No (IPv4 only) Webex third-party SIP device integration requires IPv4.
"Call on Webex" (non-PSTN) No Cisco Webex does not support third-party SIP endpoints using the basic "Call on Webex" service. A Webex Calling workspace is required.


Cisco Webex Calling Workspace

Before configuring the Zenitel device, create a workspace in Cisco Webex Control Hub and add the device as Customer Managed Devices > Generic IPPhone Customer Managed.

During workspace creation, Webex generates the SIP credentials required by the Zenitel device. These values will be used in the Zenitel SIP account configuration.

  • SIP Username
  • SIP Password
  • Line ID
  • SIP Domain
  • Outbound Proxy
OBS icon The generated SIP password is displayed only once. Record it securely before closing the dialog.


Cisco Webex Control Hub workspace credentials used during SIP configuration


Configuration of Zenitel Device

SIP Account

Log in to the Zenitel device and navigate to SIP Configuration > Account/Call. Configure the SIP account using the credentials obtained from Webex Control Hub. The mapping between the Webex credentials and the corresponding fields in the Zenitel device is shown below.


Parameter Mapping
Webex Control Hub Zenitel SIP Configuration
SIP Username Authentication User Name
SIP Password Authentication Password
Line ID Number (SIP ID)
SIP Domain Server Domain (SIP)
Outbound Proxy Outbound Proxy


Mapping of Cisco Webex Calling credentials to Zenitel SIP account settings


Media and Transport Settings

Configure the following parameters:

  • Outbound Transport = ANY
  • SIP Scheme = sip
  • RTP Encryption = srtp_encryption
  • SRTP Crypto Type = AES_CM_128_HMAC_SHA1_80

Save the configuration and verify that the SIP account successfully registers towards Webex Calling.


Additional Configuration

DNS Server

A DNS server capable of resolving public DNS SRV records is required for Webex service discovery.

Configure the DNS server under Main > Main Settings on the Zenitel device.

For additional information about how Zenitel devices locate Webex services, see DNS SRV support in SIP mode.

Door Opening

If the station relay is used for door opening, configure DTMF Method = RFC 2833 in SIP Configuration > Account/Call > Call Settings.

Cisco Webex supports RFC 2833 DTMF signaling for relay activation. SIP INFO is not supported.

Video Devices

For video-capable Zenitel devices such as the TCIV+, ZDD, and ITSV series, ensure that video is enabled.

For native Zenitel devices, including TCIV+, TMIV+, and TEIV+, enable the SendRecv option in Video Settings when video transmission from the station is required. For details, see Video Settings.

The ZDD device uses the SendRecv setting by default and requires no additional configuration.

ZIPS Audio Kit

If no audio is heard when using a ZIPS Audio Kit, check the conversation mode. Enable Advanced configuration and go to SIP Configuration > Account/Call > Call Settings and set Conversation mode = Duplex.


Related article