|
|
| (76 intermediate revisions by 2 users not shown) |
| Line 1: |
Line 1: |
| − | [[File:IP Video Door Station.PNG|thumb|600px|IP Video Station, item 1401110200]] | + | {{obsolete}} |
| | + | {{APS}} |
| | + | [[File:IP Video Door Station.PNG|thumb|600px|IP Video Station with Axis camera, item 1401110200]] |
| | | | |
| − | The STENTOFON Vandal Resistant '''IP Video Station''' (item 1401110200) is tough, durable and resilient, and designed for use in the harshest of environments. The station is typically used as a communication, information or emergency point and connects directly to the IP network making it easy to deploy – anywhere and at any distance. Designed for CCoIP® the station offers a set of critical communication features such as integrated firewall, group call, call priority and over-ride, to name just a few. This enables you to deliver instant, efficient and secure voice, video and data services in an IP environment.
| + | == Connections == |
| | + | * [[IP Video Doorstation Connections|Intercom connections]] |
| | | | |
| − | ==Installation== | + | ==Configuration== |
| − | See article: [[IP Station Installationxx]]
| + | The station can operate in three different modes, depending on what kind of server the station should register to. Choose one of the links below according to what mode you need to configure. |
| | | | |
| − | ==Station Board Connectors and LED Indications==
| + | General configuration: |
| − | See article: [[IP_Station_Board_Connections_and_Indications#8022_-_IP_Substation|IP Station Board Connections and Indications]]
| + | * [[IP Station Configuration - ICX-AlphaCom mode]] |
| | + | * [[SIP Intercom - Web Interface|IP Station Configuration - SIP mode]] |
| | + | * [[IP Station Configuration - Pulse mode]] |
| | | | |
| − | == IP Station Configuration ==
| + | Station specific configuration: |
| − | See article: [[IP_Station_Configuration#Configuration_in_IP-StationWeb]]
| + | * [[Axis Camera Configuration]] |
| | | | |
| − | ==Reset to factory settings== | + | == Restore Factory Defaults and Software Upgrade == |
| − | See article: [[IP_Station_Restore_Factory_Defaults|IP Station Restore Factory Defaults]]
| + | * [[INCA Station Restore Factory Defaults|Factory reset of the intercom station]] |
| | + | * [[INCA Station Software upgrade|Upgrade via the station web interface]] |
| | + | * [[IMT - Discover & Upgrade|Upgrade using the IMT tool]] |
| | + | * Axis Camera upgrade |
| | + | * [[Automatic Software Upgrade|Automatic Software Upgrade (SIP mode only)]] |
| | + | * [[:Category:INCA Release notes|Software Release Notes]] |
| | | | |
| − | ==Software Upgrade== | + | == Connectors, Indicators and Dimensions == |
| − | See article: [[IP Station Software upgrade]]
| + | * [[INCA Video Doorstation Board Connectors|Board Connectors]] |
| | + | * [[INCA Video Doorstation LED Indicators|Station LED Indications]] |
| | + | * [[INCA Substation PCB LED Indicators|PCB LED Indications]] |
| | + | * [[IP Video Doorstation Dimensions & Mounting Instructions|Dimensions]] |
| | | | |
| − | ==Dimensions== | + | == Accessories == |
| − | See article: [[IP_Stations_Dimensions_%26_Mounting_Instructionsxx|IP Stations Dimensions and Mounting Instructions]]
| + | * [[Back box flush mount - 1401199101]] |
| | + | * [[Back box on wall mount - 1401199111]] |
| | + | * [[Protection Roof - 1401199112]] |
| | | | |
| − | =Camera configuration= | + | == Additional information == |
| | + | * [http://www.zenitel.com/product/ip-vandal-resistant-video-station Additional Documentation on Zenitel.com] |
| | | | |
| − | Connect to the camera using a webbrowser on default IP address 169.254.1.101.
| |
| | | | |
| − | In the menu that appears, click '''System Settings''', and you will be asked to login:
| + | [[Category: Discontinued Stations]] |
| − | | |
| − | Username: '''admin''' <br/>
| |
| − | Password: '''1234'''
| |
| − | | |
| − | Set to factory default:
| |
| − | ===CP-Cam Factory Reset===
| |
| − | '''This should be carried out only by experienced technicians. The customer is liable for damages caused by improper opening of the housing. '''
| |
| − | | |
| − | If the entered IP address is unknown, it is possible to reset the address to 169.254.1.101 using the DIP switch. To proceed, the unit must be opened.
| |
| − | ''Note: A change of the IP address is made via the web interface of the CP-CAM.''
| |
| − | The procedure is as follows:
| |
| − | :1. Open the CP-CAM so the two DIP switches are accessible ( see picture ).
| |
| − | :2. Note the switch position and then turn both switches to „OFF“.
| |
| − | :3. Connect PC with the IP number range 169.254.1.xxx and set the desired IP address in the web interface.
| |
| − | :4. Turn switch positions back to original positions.
| |
| − | :5. Close housing properly.
| |
| − | | |
| − | [[File:CP-CAM.PNG|thumb|500px|left]]
| |
| − | <br style="clear:both;" />
| |
| − | | |
| − | ===Axis Factory Reset===
| |
| − | To restore the factory settings, proceed as follows:
| |
| − | :1. Disconnect the camera from the power supply and ethernet.
| |
| − | :2. Remove the four screws securing the rear cover and remove it.
| |
| − | :3. Keep the Control button pressed while you restore the power supply.
| |
| − | :4. Hold down the button for about 15 seconds until the status LED is yellow flashing.
| |
| − | :5. Release the Control Button. The process is complete when the status LEDs light up green.
| |
| − | | |
| − | [[File:Axis.PNG|thumb|left|500px]]
| |
| − | <br style="clear:both;" />
| |
| − | | |
| − | ''If no DHCP server is active on your network the new default IP is '''192.168.0.90'''.''
| |
| − | ''The new default user is '''root''' with password '''pass'''''
| |
| − | | |
| − | =Setup with STENTOFON Video Display Station=
| |
| − | To configure the STENTOFON Video Display Station please see: [[IP Desktop Station with Video Display - 1408001635]]
| |
| − | | |
| − | This chapter describes the steps for configuring the CP-Cam:
| |
| − | | |
| − | From the Main Menu select '''System Settings > Network'''
| |
| − | :1. Under section '''IP-SETUP''', set ''IP-SETUP Type'' to '''Manual'''
| |
| − | [[File:IP-VideoDoorStation1.png|left|thumb|500px]]
| |
| − | <br style="clear:both;" />
| |
| − | :2. Enter a static IP adresss, Netmask, Gateway and DNS
| |
| − | :3. Under section '''System''', set ''Authentication required for Picture/Video'' to '''No'''
| |
| − | [[File:IP-VideoDoorStation2.png|left|thumb|500px]]
| |
| − | <br style="clear:both;" />
| |
| − | :4. Click '''Save Changes''' at the bottom of the page
| |
| − | <br style="clear:both;" />
| |
| − | ----
| |
| − | | |
| − | From the Main Menu select '''System Settings > Camera'''
| |
| − | :1. Under section '''Settings''', set ''Mode'' to '''Custom'''
| |
| − | :2. Set '''Res X''' to 320
| |
| − | :3. Set '''Res Y''' to 240
| |
| − | [[File:IP-VideoDoorStation3.png|left|thumb|500px]]
| |
| − | <br style="clear:both;" />
| |
| − | :4. Under section '''Settings''', set ''Frames per Second (Sensor)'' to '''15'''
| |
| − | [[File:IP-VideoDoorStation4.png|left|thumb|500px]]
| |
| − | <br style="clear:both;" />
| |
| − | | |
| − | =Setup with 3rd party Video devices=
| |
| − | ==Milestone==
| |
| − | It is assumed that a Milestone XProtect system is already installed and up and running. The latest Milestone XProtect Professional and Smart client can be downloaded from Milestonesys.com.
| |
| − | | |
| − | The version used in the examples that follows is XprotectPro V8.1a
| |
| − | | |
| − | Open the XProtect Professional Management Application by double clicking the desktop icon. Expand the mennu tree strcture and right click ''Hardware Devices''. Select '''Add New Hardware Device'''
| |
| − | [[File:Milestone4.PNG|left|thumb|500px]]
| |
| − | <br style="clear:both;" />
| |
| − | --------------------------
| |
| − | Choose '''Manual''' as the hardware detection method.
| |
| − | [[File:Milestone5.PNG|left|thumb|500px]]
| |
| − | <br style="clear:both;" />
| |
| − | --------------------------
| |
| − | *1 Enable ''Use''
| |
| − | *2 Type in the IP address of the camera in the ''Address'' field
| |
| − | *3 Select username '''admin''' from the dropdown box under ''User Name''
| |
| − | *4 Enter the default IP Video Door Station camera password: 1234 in the ''Password field''
| |
| − | *5 In the ''Hardware Driver'' dropdown box, scroll down and select '''Universal Driver'''
| |
| − | *6 Repeat for 1-5 the next camera(s)
| |
| − | *7 Click '''Next''', followed by '''Finish''' in the next window.
| |
| − | [[File:Milestone6.PNG|left|thumb|500px]]
| |
| − | <br style="clear:both;" />
| |
| − | --------------------------
| |
| − | After adding the new camera(s) to the device list, they should appear in the tree structure under ''Cameras and Storage Information''. Right click the IP Video Station camera and select '''Properties'''
| |
| − | [[File:Milestone3.PNG|left|thumb|500px]]
| |
| − | <br style="clear:both;" />
| |
| − | --------------------------
| |
| − | If the image in the preview window is visible, no more actions are required.
| |
| − | | |
| − | If there is no image shown from the camera, click on the ''Camera Settings...'' button.
| |
| − | [[File:Milestone2.PNG|left|thumb|500px]]
| |
| − | <br style="clear:both;" />
| |
| − | --------------------------
| |
| − | In the Video Properties set:
| |
| − | *1 Codec: JPEG
| |
| − | *2 Streaming mode: HTTP
| |
| − | *3 Delivery mode: Multipart stream
| |
| − | *4 Retrieval mode: Streaming
| |
| − | *5 Connection URI: <nowiki>http://<camera IP address>/mjpg/video.mjpg</nowiki>
| |
| − | *6 Click ''Preview Image'' to verify that the image is shown, followed by clicking ''OK''.
| |
| − | [[File:Milestone1.PNG|left|thumb|500px]]
| |
| − | <br style="clear:both;" />
| |
| − | --------------------------
| |
| − | | |
| − | | |
| − | | |
| − | [[Category: Stations]] | |
| − | [[Category: IP Stations]]
| |
| − | [[Category: Vandal Resistant Stations]]
| |
| − | [[Category: Video]]
| |
