Configuration of the ZDD-1 (Edge/SIP)

This article describes configurations that are specific to the ZDD-1 intercom when used in SIP mode or Edge mode.

GUI Settings

Log in to the ZDD-1 and navigate to the GUI Settings.

General Settings

General Settings

Themes options

• Screen: This is fixed. The ZDD-1 uses a 7" screen with 15:9 aspect ratio
• Theme: Options are:
  • Light: Standard light theme. 6 entries per page. (Default theme)
  • Dark: Standard dark theme. 6 entries per page.
  • Light Compact: Light theme for display, with compact elements. 8 entries per page.
  • Custom: Custom color theme. With this theme you get an option to select your own color from a color palette. 6 elements per page.

• Language: Sets the language for the text in the display. Available languages: English, French, German, Dutch, Italian, Spanish, Norwegian, Swedish and Danish. Note: The language in the web interface will not change.
• Time Format: Select if the time shown in the top right corner of the display should be in 12 or 24 hour format.
• Use Custom Background Image: Enable if you want to use upload your own image to use as background.
• Background Image: Select "Choose File" and browse for the file to upload. The file must be in .jpg or .png format, and resolution minimum 768x1280 pixels. Size maximum 1 MB.

Display Video

The ZDD-1 Door Intercom supports two-way video.

Display Video

• Enable Far End Video: Check this box if you want video to be displayed in the ZDD-1 during a call with a video enabled device (Such as ITSV-5). Default disabled.
• Display Video Mode: Select how the video from the remote device should be presented:
  • Add black margins proportionally (default)
  • Original Proportion
  • Cut proportionally

Two-way video: Two-way video is supported when the call is initiated from the ZDD-1. The ZDD-1 does not display video on incoming calls to the ZDD-1 When the ZDD-1 is used with an ICX-AlphaCom system two-way video is not supported. In this case only video from ZDD-1 to the video enabled device (Such as ITSV-5) is supported.

Display Headers

ZDD-1 offers an option to show two lines of text in the top left corner of the display. This can typically be Company name and Address.

Display Headers

Display Header in ZDD-1

Address Book

In the Address Book section under the "GUI Settings", press the "+" button to "Add New Entry":

• Name: Is the main label of the entry
• Location: Is a sub-label in smaller fonts (optional)
• Number: The extension number to dial when the entry is pressed
• Ringlist: An option to call using the RingList of the station. This is typically used if there is a need to call multiple stations in sequence or in parallel. The RingList is configured from the Direct Access Key settings.

• Select Logo: One can upload an image for the entry. In the station display the image will appear at the right side of the entry. The file must be in .svg format.
• Delete Logo: Deletes the image

Use the UP and DOWN arrows to the left of the entry to move the entry up or down in the list, and the Recycle Bin icon to delete an entry.

Address Book

The ZDD-1 supports up to 50 entries.

Display

Log in to the ZDD-1 and navigate to the Display setting.

Brightness Mode Settings

When Brightness Mode is set to Manual, one can adjust the Brightness with a slider from 0 (off) to 100. The value 50 is default.

When Brightness Mode is set to Automatic, the brightness is controlled by the sensor on the front panel, and will adjust automatically according to ambient brightness. When enabling Advanced Configuration mode one get the following options in addition:

• Brightness Offset: Adjust the deviation from the automatic brightness level in the range -99 to +99. Default value = 0.
• Brightness Levels: Allows choosing the granularity of the automatic brightness levels in the range 5 to 20. A bigger number means more gradual brightness transitions. Default value = 5.
• Transition Delay: Time between a sudden brightness change in front of the sensor and the corresponding brightness adjustment. Range: 1 to 10 seconds. Default = 1 second.

Automatic Brightness adjustments

Display Timeout Settings

• Display Timeout: When enabled the display will go to "sleep mode" after a preset time. When the display goes to sleep, one can choose to reduce the brightness, and/or to show the background image:
• Enable Timeout Brightness: When enabled the display will change the brightness when going to sleep mode, the brightness will be according to the "Timeout Brightness" setting.
  • Timeout Brightness: This sets the brightness level when the display goes to sleep (default = 5).
• Enable Background Overlay: When enabled the background image will be displayed when the display goes to sleep mode.
• Timeout: After a call is ended (or motion is not detected) the display will go to "sleep mode" after this time.
• Wake On Motion: When enabled the display will "wake up" when the sensor detects motion in front of the station. Note: The display will always wake up when touched.
  • Maximum Detection Distance: Sets the max. distance for detecting the motion. Range is 0.5 to 2.0 meters (Default = 2m).
  • Detection Sensitivity: Sets how sensitive the detection should be in 5 levels; Low, Medium Low, Medium, Medium High, High (default)

Display Timeouts