Difference between revisions of "RCI - Remote Control Input"

Revision as of 10:09, 14 October 2013

Examples of RCI usage

A Remote Control Input (RCI) is triggered by an external potential-free contact.

Inputs

Typical external triggers are fire and gas alarm systems, temperature detectors, doors, lifts, alarm buttons etc.

An RCI signal can be received by a number of devices:

Device	# of RCI's
AlphaCom XE20/26	6
AlphaCom XE7/1	2
IPARIO unit (IP)	8
RIO unit (analog)	8
IP Substation	3
IP Flush Master	3
IP Turbine station	6

The AlphaCom XE supports up to 140 inputs.

RCI inputs in an AlphaCom XE20 and XE26

RCI inputs in an AlphaCom XE7

RCI inputs in an AlphaCom XE1 (top lid removed)

Actions

The set-up for the RCI input and the actions you want it to activate is very flexible. An RCI can activate almost any function in the exchange by using action commands, either Built-In Action Commands or Data Protocol Commands. The configuration of the RCI's is done with the AlphaPro programming tool.

Some examples of features that can be activated:

Dispatch prerecorded voice messages to stations and PA system (fire alarm etc.)
Show status information on a DAK48 panel, e.g. door open/closed
Send text message to a station or a group of stations, e.g. temperature warning
Set up group calls, audio program or conferences
Activate Call Forwarding
Control Remote Control Output

etc.

Configuration

In AlphaPro there is an RCI table, where the physical address is entered, along with the desired actions. The physical address is given as device + pin-number.

For internal RCIs in the AlphaCom, the device address is 65-68, and the pin number is 1-6.
Internal pin number 8 is the temperature alarm.
Mappings for the internal RCI's are autoloaded. Mappings for external RCI's (Slave modules, RIO's, IPARIO, stations) must be manually programmed.

	RCI Type	Device/Station physical Number	Pin Number
AlphaCom XE20/XE26	Device	65 - 68	1 - 6
AlphaCom XE7/XE1	Device	65 - 68	1 - 2
IPARIO unit (IP)	Station	1 - 552	1 - 8
RIO unit (analog)	Device	1 - 64	1 - 8

RCI configuration window. Here input 2 will trigger voice alarm message number 3 to group 1, and turn on the RCO 5

Inputs from IP Stations must be configured using the Event Handler.

	RCI Type	Station Physical Number (Event Owner)	Pin Number (Sub-Event)
IP Substation	Station	1 - 552	1 - 3
IP Flush Master	Station	1 - 552	1 - 3
IP Turbine station	Station	1 - 552	1 - 6

Event Handler configuration window. Here Input 2 (DAK 2) will trigger alarm message 3 to group 1, and turn on RCO 5

Software

AMC 10.50 or later supports RCI's in slave module (devices 66-68). (The software in the slave modules must also be upgraded)

@@ Line 57: / Line 57: @@
 ! style="background:#ffdead;" width="200" |&nbsp;
 ! style="background:#ffdead;" width="70" |RCI Type
-! style="background:#ffdead;" width="70" |Device/Station Number
+! style="background:#ffdead;" width="150" |Device/Station physical Number
 ! style="background:#ffdead;" width="70" |Pin Number
 |-
@@ Line 67: / Line 67: @@
 |-
 | [[RIO|RIO unit]] (analog) || align=center | Device || align=center | 1 - 64 || align=center | 1 - 8
+|-
+|}
+[[File:RCI AlphaPro.png|left|thumb|500px|RCI configuration window. Here input 2 will trigger voice alarm message number 3 to group 1, and turn on the RCO 5]]
+<br style="clear:both;" />
+Inputs from IP Stations must be configured using the Event Handler.
+{| border="1"
+! style="background:#ffdead;" width="200" |&nbsp;
+! style="background:#ffdead;" width="70" |RCI Type
+! style="background:#ffdead;" width="150" |Station Physical Number (Event Owner)
+! style="background:#ffdead;" width="150" |Pin Number (Sub-Event)
 |-
 | [[IP_Station_Board_Connections_and_Indications#8022_-_IP_Substation|IP Substation]] || align=center | Station || align=center | 1 - 552 || align=center | 1 - 3
@@ Line 76: / Line 89: @@
 |}
-[[File:RCI AlphaPro.png|left|thumb|right|500px|RCI configuration window. Here input 2 will trigger voice alarm message number 3 to group 1, and turn on the RCO 5]]
+[[File:DakAsRCI.PNG|left|thumb|500px|Event Handler configuration window. Here Input 2 (DAK 2) will trigger alarm message 3 to group 1, and turn on RCO 5]]
 <br style="clear:both;" />