Search results

Create the page "AS" on this wiki! See also the search results found.

Flowire CCo
...and FCDC1/2, FCDC1/2 should be set as "Not CCo", and one FCDC3 must be set as "CCo".}} ...Flowires as forced CCo, <u>then all the others in the cluster must be set as '''not CCo'''!</u>

2 KB (320 words) - 13:40, 12 May 2020
Collecting log file (AlphaPro)
...mmunication program) runs, which means the log file must be copied as soon as the error has occured and before Wacs (Send/Get) is run again. }}

603 bytes (97 words) - 10:54, 24 October 2023
Stentofon DotNet Libraries
One single node as well as a complete AlphaCom node network is supported. ...lications interfacing the AlphaCom, [[VS-SDK for AlphaCom]] is recommended as a start.

1 KB (183 words) - 11:27, 9 February 2023
MPC Data Protocol
...mapping MPC commands to AlphaCom commands one-to-one it can be thought of as a variant of the [[Data link layer#Stentofon Simple Link Layer|simple link As from software 11.2.3.5 the MPC input commands also support global numbers,

993 bytes (157 words) - 14:24, 7 September 2017
DTMF During Connection
255 = Activate "DTMF transmission mode". Succeeding digits are transmitted as DTMF tones 0-9. DAK 1 and 2 will generate "*" and "#". * When parameter 1 = 255 the DTMF tone is transmitted as long as the digit is pressed.

2 KB (252 words) - 15:45, 20 May 2022
Linux
...re, including desktop computers, supercomputers, and embedded devices such as mobile phones and routers.

1 KB (190 words) - 08:08, 8 September 2017
Fault Relay - Manual Reset
This default error message is sent as a display mail with priority 80. This will trigger event 6 - Priority Mail Present. This event is on as long as there are priority mails in queue, and goes off when queue is empty. Displa

1 KB (248 words) - 10:22, 25 May 2022
Stentofon.AlphaCom.Data.dll - Release Notes
...ormance to accepted standards on .NET assembly naming conventions, as well as namespace naming conventions. Also better separation of functionality like

822 bytes (104 words) - 10:33, 26 October 2017
I/O Settings (Pulse)
...O should be used as an Input or as an Output. By default all I/O's are set as Inputs. ===Use Inputs As Key Matrix===

3 KB (394 words) - 10:42, 9 February 2023
I/O Settings (Edge)
...O should be used as an Input or as an Output. By default all I/O's are set as Inputs. ...contact (referred to as "NO - Normally Open"). The input can be configured as "Input NC" (NC - Normally Closed) instead. (Requires firmware 8.1.3.0 or la

3 KB (457 words) - 11:17, 12 January 2024
VS-Operator Server Setup Connection Error
...tool cannot connect to the required SQL server instance. An error message as displayed in the picture below will be shown. * Check the name of the instance as displayed in Management Studio

691 bytes (102 words) - 10:39, 29 June 2023
EA1400
...ker lines. The audio output channels can be monitored for line faults such as shorts circuits and ground faults. * [[VoIP kit as PA Interface]]

830 bytes (117 words) - 13:46, 5 July 2022
Recorder 2.0 no audio recorded
Incorrect Recorder Initial Configuration can cause the recorder to act as if it's working, but there are no audio packets recorded. Note that this IP Address also cannot be the link-local address (127.0.0.1), as it's used to direct the ICX-AlphaCom or AlphaCom server to send the audio p

693 bytes (109 words) - 09:28, 14 February 2024
I/O Settings (SIP)
...O should be used as an Input or as an Output. By default all I/O's are set as Inputs. ...contact (referred to as "NO - Normally Open"). The input can be configured as "Input NC" (NC - Normally Closed) instead. (Requires firmware 8.1.3.0 or la

3 KB (465 words) - 11:17, 12 January 2024
Keyboard matrix - TKIE-3
* [[Inputs as Key Matrix (ICX-AlphaCom)]] * [[I/O Settings (Edge)|Inputs as Key Matrix (Edge)]]

1 KB (189 words) - 18:09, 14 November 2023
Voice Help
...e carrying out the next step in a function. The help message stops as soon as you proceed (i.e. press a key).

839 bytes (134 words) - 16:46, 24 January 2017
Turbine Inputs and Outputs in ICX-AlphaCom
...2FO_Settings|web page of the Turbine device]]. By default all I/Os are set as inputs. ...K|DAK table]], or one can use the [[Event Handler]]. DAK keys are reported as [[Station Input or Station DAK key (Event Type)|Event 30 - Station Input or

3 KB (461 words) - 11:21, 23 June 2023
Private break-in
...rivate ringing with one-way audio. The break-in function is active as long as the station holds down the M-key. When M-key is released the conversation g

806 bytes (116 words) - 09:39, 8 October 2019
%1.udp
* Returns the [[UDP group]] memberships for station, as a decimal number. * Interpret the number as a bitmap, bit#0 is UDP group 1, bit#7 is UDP group 8.

711 bytes (96 words) - 09:46, 4 October 2019
Disconnect own station from ongoing group call feature
...r this station. (C-press in conversation just disconnects the conversation as before). *Disconnect-from-groupcall is also available as a data protocol message [[ST GROUP DISCON]].

953 bytes (128 words) - 09:47, 8 October 2019

Special

Search results