Search results
Create the page "AS" on this wiki! See also the search results found.
- ...ot being brought into Feenics, you will need to uncheck CCoIP for each one as this helps to not expose it to the import process. ...to complete this task will result in a fail import message for ~30 seconds as the system executes health checks.14 KB (2,263 words) - 15:21, 9 September 2024
- ...the other intercom stations in the system. Most Zenitel IP devices can act as an Edge Controller, see [[Edge Controller|full list here]]. By default call buttons aren't programmed on IP substations as the programming of DAK keys and Ringlist is done via '''Edge Controller'''13 KB (2,186 words) - 15:15, 29 August 2023
- As an option it is possible set a conversation timer, and play a voice message ...econd DAK-48 panel must be added. Function keys on the DAK48 panel will be as follows:11 KB (1,810 words) - 11:53, 10 February 2023
- **1.0.3.0 - do not configure CRMV as part of a Ringing Group **13.1.3.2 - do not configure CRMV as part of a Ringing Group24 KB (3,826 words) - 15:45, 22 November 2023
- This station is fully supported as from from AlphaCom version 11.2.3.72 KB (222 words) - 13:49, 29 January 2024
- This station is fully supported as from AlphaCom version 11.2.3.112 KB (216 words) - 12:52, 28 November 2023
- This station is fully supported as from AlphaCom version 11.2.3.112 KB (216 words) - 12:52, 28 November 2023
- reported to AlphaWeb as well as to 3rd party management systems using SNMP, Syslog or OPC. ...r “Micro Zone PA”, e.g. when you only want to address a specific area such as a guard room, elevator, patient waiting room etc.5 KB (731 words) - 12:52, 23 June 2022
- * SIP as station ...IP phone as a trunk, but it is usually better to connect single telephones as "SIP station", see below.23 KB (3,518 words) - 13:45, 23 February 2023
- |'''Parameter 2''': || Mail Flag bits as described in [[SEND_MAIL#Mail_flags | SEND MAIL]]2 KB (268 words) - 09:35, 8 October 2019
- * Set up Zenitel Client as a Pulse client As there are many options in the Configuration step, we will only describe the9 KB (1,460 words) - 11:36, 29 June 2023
- * Can be used as wall mounted station using the optional bracket 10080911002 KB (223 words) - 14:02, 2 May 2023
- This station is fully supported as form AlphaCom version 10.502 KB (258 words) - 14:18, 12 February 2024
- ...a call can automaticaly be placed to a preconfigured number. This is known as '''Hotline Call'''. By default there is a delay of 5 seconds before the cal2 KB (328 words) - 09:58, 24 May 2022
- * The Control Room should be configured as a CRM (Control Room Master), the DAK display should be enabled, and the Nav2 KB (266 words) - 17:23, 6 November 2013
- * Can be used as wall mounted station using the optional bracket 10080911002 KB (225 words) - 13:59, 2 May 2023
- ...ecific DAK if there is an incoming call from a destination that is defined as Directory Number for a specific DAK call action (under DAK settings). Defau2 KB (233 words) - 15:01, 12 September 2019
- * An event such as a call or call request can be used to connect a camera to a monitor and ins2 KB (259 words) - 16:03, 15 August 2022
- * To receive information about Call Button pressed, "'''Report DAK as Digital Input in ONVIF'''" option must be enabled in the Zenitel device pri ...s (In Conversation, Ringing, In call queue), the "'''Report station events as Digital Input in ONVIF'''" must be enabled in the Zenitel device prior to d5 KB (809 words) - 14:25, 26 September 2022
- ...possible to configure ONVIF Backchannel gain via the device web interface as some VMSes do not support setting the backchannel gain2 KB (211 words) - 10:08, 21 June 2024