|
|
| (65 intermediate revisions by 2 users not shown) |
| Line 1: |
Line 1: |
| − | [[File:IP Video Door Station.PNG|thumb|600px|IP Video Station, item 1401110100]] | + | {{Obsolete}} |
| | + | {{AEIPS}} |
| | + | [[File:IP Video Door Station.PNG|thumb|600px|IP Video Station with CP-CAM camera, item 1401110100]] |
| | | | |
| − | '''Camera Type: CP-Cam'''
| + | == Connections == |
| | + | * [[IP Video Doorstation Connections|Intercom connections]] |
| | | | |
| − | * Default IP adresses:
| + | ==Configuration== |
| − | ** Audio module: 169.254.1.100 (admin/alphaadmin)
| + | The station can operate in three different modes, depending on what kind of server the station should register to. Choose one of the links below according to what mode you need to configure. |
| − | ** Camera module: 169.254.1.101 (admin/1234)
| |
| | | | |
| − | ===<u>Highlights</u>===
| + | General configuration: |
| − | * Robust housing with Aluminium frontplate | + | * [[IP Station Configuration - ICX-AlphaCom mode]] |
| − | * IP65 protection to front | + | * [[Adding station to existing system (Edge)|IP Station Configuration - Edge mode]] |
| − | * Powered from the IP network cable using Power over Ethernet (PoE)* PoE Powered from one IP network cable
| + | * [[SIP Intercom - Web Interface|IP Station Configuration - SIP mode]] |
| − | * Relay output for remote control, e.g. doors, signal lamps and gates | + | * [[IP Station Configuration - Pulse mode]] |
| − | * Button with bi-colour LED ring | |
| | | | |
| − | ===<u>[[IP Sub Connections|InterCom connections]]</u>===
| + | Station specific configuration: |
| | + | * [[CP Cam Configuration]] |
| | | | |
| − | ===<u>[[IP Station Configuration]]</u>=== | + | == Restore Factory Defaults and Software Upgrade == |
| | + | * [[INCA Station Restore Factory Defaults|Factory reset of the intercom station]] |
| | + | * [[CP-Cam Factory Reset|Factory reset of the Camera Module]] |
| | + | * [[INCA Station Software upgrade|Upgrade via the station web interface]] |
| | + | * [[IMT - Discover & Upgrade|Upgrade using the IMT tool]] |
| | + | * CP Cam upgrade |
| | + | * [[Automatic Software Upgrade|Automatic Software Upgrade (SIP mode only)]] |
| | + | * [[:Category:INCA Release notes|Software Release Notes]] |
| | | | |
| − | ===<u>[[INCA Station Software upgrade|Software Upgrade]]</u>=== | + | == Connectors, Indicators and Dimensions == |
| | + | *[[INCA Video Doorstation Board Connectors|Board Connectors]] |
| | + | * [[INCA Video Doorstation LED Indicators|Station LED Indications]] |
| | + | * [[INCA Substation PCB LED Indicators|PCB LED Indications]] |
| | + | * [[IP Video Doorstation Dimensions & Mounting Instructions|Dimensions]] |
| | | | |
| − | ===<u>[[INCA Substation LED Indicators|LED Indications]]</u>=== | + | == Accessories == |
| − | | |
| − | ===<u>[[INCA Substation Board Connectors|Board Connectors]]</u>===
| |
| − | | |
| − | ===<u>[[IP Video Doorstation Dimensions & Mounting Instructions|Dimensions]]</u>===
| |
| − | | |
| − | ===<u>[[INCA Station Restore Factory Defaults|Reset to factory settings]]</u>===
| |
| − | | |
| − | ===<u>[http://www.zenitel.com/product/ip-vandal-resistant-video-intercom-station-w-cp-cam-camera Additional Documentation on Zenitel.com]</u>===
| |
| − | | |
| − | [[Category: INCA Stations]]
| |
| − | | |
| − | | |
| − | ==Installation==
| |
| − | See article: [[IP Station Installation]]
| |
| − | | |
| − | ==Station Board Connectors and LED Indications==
| |
| − | See article: [[IP_Station_Board_Connections_and_Indications#1401110100.2F1401110100|IP Station Board Connections and Indications]]
| |
| − | | |
| − | == IP Station Configuration ==
| |
| − | See article: [[IP_Station_Configuration#Configuration_in_IP-StationWeb|IP Station Configuration]]
| |
| − | | |
| − | ==Reset to factory settings==
| |
| − | *Factory Settings of Audio Module: [[IP_Station_Restore_Factory_Defaults|IP Station Restore Factory Defaults]]
| |
| − | *Factory Settings of Camera Module: [[#CP-Cam Factory Reset]]
| |
| − | | |
| − | ==Dimensions==
| |
| − | See article: [[IP_Stations_Dimensions_%26_Mounting_Instructions#IP_Video_Door_Station|IP Stations Dimensions and Mounting Instructions]]
| |
| − | | |
| − | ==Related articles==
| |
| | * [[Back box flush mount - 1401199101]] | | * [[Back box flush mount - 1401199101]] |
| | * [[Back box on wall mount - 1401199111]] | | * [[Back box on wall mount - 1401199111]] |
| − | * [[Protection Roof - 1401199121]] | + | * [[Protection Roof - 1401199112]] |
| − | | |
| − | ==Camera Configuration==
| |
| − | Connect to the camera using a webbrowser on default IP address 169.254.1.101.
| |
| − | | |
| − | In the menu that appears, click '''System Settings''', and you will be asked to login:
| |
| − | | |
| − | Username: '''admin''' <br/>
| |
| − | Password: '''1234'''
| |
| − | | |
| − | It is recommended to use a static IP address for the camera:
| |
| − | | |
| − | [[File:Cam 29.PNG|thumb|left|500px|Setting Static IP Address]]
| |
| − | <br style="clear:both;" />
| |
| − | | |
| − | From the Main Menu navigate to '''System Settings -> Camera''':
| |
| − | | |
| − | [[File:Cam 28.PNG|thumb|left|500px|CP-CAM Configuration]]
| |
| − | <br style="clear:both;" />
| |
| − | | |
| − | ===CameraWeb===
| |
| − | '''Main Menu'''
| |
| − | | |
| − | [[File:Cam 1.PNG|thumb|left|500px|Camera Main Menu]]
| |
| − | <br style="clear:both;" />
| |
| − | ------
| |
| − | '''View Picture/Slideshow
| |
| − | [[File:Cam 2.PNG|thumb|left|500px|View single picture or slideshow]]
| |
| − | <br style="clear:both;" />
| |
| − | This option is used to display single pictures fo the camera. <br/>
| |
| − | By clicking '''Start''', the camera starts displaying a picture every second. <br/>
| |
| − | With '''Stop''', the current picture is permanently displayed. <br/>
| |
| − | With '''Back''', you return to the main menu.
| |
| − | ------
| |
| − | '''View Video'''
| |
| − | [[File:Cam 3.PNG|thumb|left|500px|View live videostream]]
| |
| − | <br style="clear:both;" />
| |
| − | With this selection, the video images are displayed. <br/>
| |
| − | Settings for the displayed video can be found under '''Settings -> Camera'''. <br/>
| |
| − | With '''Back''', you return to the main menu.
| |
| − | ------
| |
| − | '''Remote Control'''
| |
| − | [[File:Cam 4.PNG|thumb|left|500px|See the status and configure the I/O ports]]
| |
| − | <br style="clear:both;" />
| |
| − | The CP-CAM can, in conjunction with an IO interface, provide two opto-coupler inputs <u>or</u> two relay outputs. <br/>
| |
| − | A door opener or light can for example be switched vie the web interface using the outputs. <br/>
| |
| − | '''Status''' <br/>
| |
| − | ''I/O Port 1'' - Shows the status of the first I/O input <br/>
| |
| − | ''I/O Port 2'' - Shows the status of the second I/O input <br/>
| |
| − | '''I/O Control'''<br/>
| |
| − | ''I/O Port 1'' - The switching state of the first output can be set here <br/>
| |
| − | ''I/O Port 2'' - The switching state of the second output can be set here <br/>
| |
| − | Off - Output alway off <br/>
| |
| − | On - Output is permanently switched on <br/>
| |
| − | Timed Switched On - Here, the output can be set for a given time period <br/>
| |
| − | Reboot System - Restarts the CP-CAM <br/>
| |
| − | Send Settings - Sends the settings to the camera to be effective <br/>
| |
| − | ------
| |
| − | '''User Setup'''
| |
| − | [[File:Cam 5.PNG|thumb|left|500px|Administrate users]]
| |
| − | <br style="clear:both;" />
| |
| − | In this menu the users of the CP-CAM can be managed. A user can be assigned different permissions. <br/>
| |
| − | The availability of the video and picture display without password entry can be set under '''Settings->Network'''. <br/>
| |
| − | '''Action''' - Ability to add, change or detele a user <br/>
| |
| − | '''Username''' - In this field, user name is entered (no special characters allowed) <br/>
| |
| − | '''Access Level''' - Selection of authorixzation for a user <br/>
| |
| − | :No rights (0) - User is deactivated
| |
| − | :Viewer (2) - User has access to single picture and video display, as well as for the camera ID
| |
| − | :Remote Control (4) - User has additionally access to remote control
| |
| − | :Administration (8) - User has unrestricted access <br/>
| |
| − | '''Set New Password''' - Enter password <br/>
| |
| − | '''Repeat Password''' - Confirm password <br/>
| |
| − | '''Add New User/Change/Delete''' - By clicking on this button, the settings are applied <br/>
| |
| − | With '''Back''', you return to the main menu
| |
| − | ------
| |
| − | '''Common Settings'''
| |
| − | [[File:Cam 6.PNG|thumb|left|500px|Common Settings]]
| |
| − | <br style="clear:both;" />
| |
| − | '''Camera Name''' - The name of the camera can be set here, which is displayed as header above the video window. The name is also displayed in the password prompt window. <br/>
| |
| − | '''Firmware version''' - The installed software version on the CP-CAM is shown here.
| |
| − | '''Save Changes''' - Saves the settings permanently and you return to the main menu.
| |
| − | ------
| |
| − | '''Network Setup'''
| |
| − | [[File:Cam 7.PNG|thumb|left|500px|Common]]
| |
| − | <br style="clear:both;" />
| |
| − | '''FTP-Access''' - FTP access to the data of the CP-CAM can be turned on here <br/>
| |
| − | '''Allowed Tools''' - Specifies which support program that are allowed to access the CP-CAM <br/>
| |
| − | | |
| − | [[File:Cam 8.PNG|thumb|left|500px|IP-Setup]]
| |
| − | <br style="clear:both;" />
| |
| − | '''IP Setup Type''' <br/>
| |
| − | :Manual/DHCP - Specifies whether the network settings are to be manually or automatically assigned
| |
| − | :IP Address - IP address at which the CP-CAM can be reached on the network
| |
| − | :Netmask - The netmask is entered here
| |
| − | :Gateway - Gateway is entered here
| |
| − | :DNS - DNS server is specified here
| |
| − | | |
| − | [[File:Cam 9.PNG|thumb|left|500px|Hardware]]
| |
| − | <br style="clear:both;" />
| |
| − | '''Ethernet Mode''' - Standard settings should always be set to '''Auto'''. The other settings are only for network professional in the event of problems with the automatic <br/>
| |
| − | '''MAC Address''' - MAC address of the camere
| |
| − | | |
| − | [[File:Cam 10.PNG|thumb|left|500px|Ports]]
| |
| − | <br style="clear:both;" />
| |
| − | Note! The following port numbers must all have different values, as this can cause malfunction
| |
| − | '''Tools''' - Port for support programs <br/>
| |
| − | '''UDP-Autoomatic Cam Detection''' - UDP port for automatic detection of camera in the network using special software <br/>
| |
| − | '''UDP-Status Messages''' - UDP port for status messages <br/>
| |
| − | | |
| − | [[File:Cam 11.PNG|thumb|left|500px|System]]
| |
| − | <br style="clear:both;" />
| |
| − | '''Authentication required for picture/video''' - Specifies whether the user requires a password for the video and picture display <br/>
| |
| − | '''Automatic Cam Detection''' - Must be turned on to automatically detect several cameras over the network. Must be turned off after system installation, particularly in network where many broadcasts are sent <br/>
| |
| − | '''UDP Status Messages''' - Settings for status messages <br/>
| |
| − | Off - Camera sends no status messages <br/>
| |
| − | Message after mode change - A message is sent after each mode change. (I/O, camera driver and LED mode) <br/>
| |
| − | Cyclical message - An additional message is sent after a time interval - even if there has been no mode change <br/>
| |
| − | '''Destination IP for UDP Status''' - Destination address of status messages <br/>
| |
| − | | |
| − | [[File:Cam 12.PNG|thumb|left|500px|Save changes]]
| |
| − | <br style="clear:both;" />
| |
| − | '''Save Changes''' - Saves the settings permanently and you return to the main menu <br/>
| |
| − | ------
| |
| − | '''Camera Setup''' <br/>
| |
| − | ''Settings''
| |
| − | [[File:Cam 14.PNG|thumb|left|500px|Configuration Presets]]
| |
| − | <br style="clear:both;" />
| |
| − | '''Configuration Presets''' - Here you can select on of several configuration sets of camera settings.
| |
| − | <u>'''Warning!''' All other changes will be lost. Therefore, you should first change the default settings and then the other!</u>
| |
| − | | |
| − | [[File:Cam 15.PNG|thumb|left|500px|Mode]]
| |
| − | <br style="clear:both;" />
| |
| − | '''Mode''' - Sets the camera resolution <br/>
| |
| − | | |
| − | [[File:Cam 16.PNG|thumb|left|500px|Frames per Second (Sensor)]]
| |
| − | <br style="clear:both;" />
| |
| − | '''Number of frames per second''' - Defines the number of pictures per second which the video sensor captures. With VGA max 15 (20 at quality 40), by QVGA/QQVGA max 25 <br/>
| |
| − | | |
| − | [[File:Cam 17.PNG|thumb|left|500px|Shown Frames (Video)]]
| |
| − | <br style="clear:both;" />
| |
| − | '''Shown Frames''' - Specifies how many of the captured pictures are transmitted as video. Only every X-th picture is sent
| |
| − | | |
| − | [[File:Cam 18.PNG|thumb|left|500px|Zoom]]
| |
| − | <br style="clear:both;" />
| |
| − | '''Zoom''' - Setting of the picture enlargement
| |
| − | :Zooming is only possible with a resolution smaller than VGA (640x480).
| |
| − | :The zoom factor can only be as large as the factor which reduced the picture.
| |
| − | :So with QQVGA max 4.0x.
| |
| − | :A value to large is automatically reset to 1.0x.
| |
| − | :Generally:
| |
| − | ::(Re''solutionX * Zoom)<u><</u>640''
| |
| − | ::(Re''solutionX * Zoom)<u><</u>480''
| |
| − | | |
| − | [[File:Cam 19.PNG|thumb|left|500px|Displacement]]
| |
| − | <br style="clear:both;" />
| |
| − | '''Displacement on X-Axis/Y-Axis''' - It is possible to adjust a picture (only at resolutions < VGA). To view a certain section of the picture, move the section in the X and Y direction so far until the desired picture is visible. Incorrect values are corrected automatically!
| |
| − | :Example: At a resolution of 320x240 and 2x zoom, the center of the picture should be displayed. Th epicture must be adjusted 160 pixels in the X direction and 120 pixels in the Y direction! <br/>
| |
| − | | |
| − | [[File:Cam 20.PNG|thumb|left|500px|Quality (JPEG compression]]
| |
| − | <br style="clear:both;" />
| |
| − | '''Quality (JPEG compression)''' - A lower quality should be chosen in case the network bandwidth is not sufficient (too many users) <br/>
| |
| − | | |
| − | ''IR Lighting/Nightvision''
| |
| − | [[File:Cam 21.PNG|thumb|left|500px|IR Lighting Setup]]
| |
| − | <br style="clear:both;" />
| |
| − | '''IR Lighting Setup''' - Selection of IR lighting mode <br/>
| |
| − | Always off - IR lighting permanently off <br/>
| |
| − | Always on - IR lighting permanently on <br/>
| |
| − | Automatic - The camera measures the brightness and, if necessary, turns on the light automatically <br/>
| |
| − | Controlled by I/O - IR lighting is controlled with the 2 I/O ports <br/>
| |
| − | | |
| − | [[File:Cam 22.PNG|thumb|left|500px|Options - IR Automatic Mode]]
| |
| − | <br style="clear:both;" />
| |
| − | '''Options-IR Automaitc Mode''' - Specifies that the IR lighting can be overridden with the two I/O ports despite automatic mode <br/>
| |
| − | Override by I/O's disabled - No response when I/O ports are switched <br/>
| |
| − | Override Option 1 - If the I/O port is ON, the IR lighting is switched on by force <br/>
| |
| − | Override Option 2 - If the I/O port is on, the IR lighting is switched on by force <br/>
| |
| − | | |
| − | [[File:Cam 23.PNG|thumb|left|500px|Options - IR Controlled by I/O's]]
| |
| − | <br style="clear:both;" />
| |
| − | '''Options-IR Controlled by I/O's''' - Determines whether the IR control via the I/O ports are to be normal or inverted <br/>
| |
| − | | |
| − | [[File:Cam 24.PNG|thumb|left|500px|IR mode treshold (Shutter val)/Hysteresis]]
| |
| − | <br style="clear:both;" />
| |
| − | '''IR mode threshold (Shutter)''' - Determination of the switching threshold (shutter - light intesity) <br/>
| |
| − | '''Hysteresis''' - Hysteresis for switching threshold. Switching threshold ON = switching threshold + hysteresis. Switching threshold OFF = switching threshold - hysteresis <br/>
| |
| − | '''Switch On Delay''' - Waiting time after exceeding the threshold on until switching occurs <br/>
| |
| − | '''Switch Off Delay''' - Waiting time after falling below the threshold off until switching occurs <br/>
| |
| − | | |
| − | [[File:Cam 25.PNG|thumb|left|500px|B/W in IR/Nightvision mode]]
| |
| − | <br style="clear:both;" />
| |
| − | '''B/W in IR/Nightvision mode''' - Indicates whether the night vision should be switched to black/white mode <br/>
| |
| − | | |
| − | ''Video''
| |
| − | [[File:Cam 26.PNG|thumb|left|500px|Picture Rotation]]
| |
| − | <br style="clear:both;" />
| |
| − | '''Picture Rotation in Video Applet''' - The CP-CAM is capable of rotating the displayed picture in 90° increments, the installation position of the CP-CAM can therefore be selected. The rotation is only for the viewing in the web interface. The pictures and the motion JGPEG stream, which can be accessed over <nowiki>http://<camera-IP>/jpg</nowiki> and <nowiki>http://<camera-IP>/mjpg/video.mjpg</nowiki> respectively, are always in original position. Th eclient software resumes the picture rotation <br/>
| |
| − | Single pictures can only be rotated when the web browser supports Flash and has it installed.
| |
| − | | |
| − | ''System Info''
| |
| − | [[File:Cam 27.PNG|thumb|left|500px|Status information]]
| |
| − | <br style="clear:both;" />
| |
| − | '''Loaded Setup''' - Shows which presettings were loaded <br/>
| |
| − | '''Sensor Driver State''' - Status mode of the camera driver. Should always be on '''RUN''', otherwise the camera must be restarted <br/>
| |
| − | '''IR Lighting State''' - Shows whether the infrared lighting is turned on or off <br/>
| |
| − | '''Shutter-Value''' - Shows the current '''position''' of the integrated lens aperture of the camera. This panel provides automatic exposure compensation. This value allows conclusions to be drawn of the intensity of the current lighting. The larger the value, the less ambient light. <br/>
| |
| − | '''Chip Version''' - Version of the built-in video chips <br/>
| |
| − | '''Save Changes''' - Saves the settings permanently and you return to the main menu
| |
| − | | |
| − | ===CP-Cam IP address Reset===
| |
| − | '''This should be carried out only by experienced technicians. The customer is liable for damages caused by improper opening of the housing. '''
| |
| | | | |
| − | If the entered IP address is unknown, it is possible to reset the address to 10.10.10.10 using the DIP switch. To proceed, the unit must be opened.
| + | == Software Requirements == |
| − | ''Note: A change of the IP address is made via the web interface of the CP-CAM.''
| + | This station is fully supported as form AlphaCom version 10.20 |
| − | The procedure is as follows:
| |
| − | :1. Power off the station
| |
| − | :2. Open the CP-CAM so the two DIP switches are accessible ( see picture ).
| |
| − | :3. Note the switch position and then turn both switches to "OFF".
| |
| − | :4. Power On the station
| |
| − | :5. Connect PC with the IP number range 10.10.10.xxx and log in.
| |
| − | :6. Turn switch positions back to original positions.
| |
| − | :7. Set the desired IP address in the web interface. Press "Save Changes"
| |
| − | :8. Reboot station
| |
| − | :9. Close housing properly.
| |
| | | | |
| − | [[File:CP-CAM.PNG|thumb|500px|left]] | + | == Additional information == |
| − | <br style="clear:both;" />
| + | * [http://www.zenitel.com/product/ip-vandal-resistant-video-intercom-station-w-cp-cam-camera Additional Documentation on Zenitel.com] |
| | | | |
| | | | |
| − | [[Category: INCA Stations]] | + | [[Category: Discontinued Stations]] |
| | + | [[Category:Video]] |
