Actions

Difference between revisions of "AlphaCom XE7"

From Zenitel Wiki

(Analogue Intercom Stations)
 
(36 intermediate revisions by the same user not shown)
Line 34: Line 34:
  
 
<br> <br>
 
<br> <br>
 +
 +
== Configuration==
 +
* [[AlphaPro]] is the Windows application used for configuring the AlphaCom XE system. Configuration of user data, such as Directory Numbers, Direct Access Keys, Group Calls etc. is done from AlphaPro.
 +
* [[AlphaWeb]] is the embedded web server running on AlphaCom XE. The AlphaWeb server provides functions for system monitoring, system configuration, and system upgrade. Initial connection is done by connecting a laptop to Eth 0 port, open a web broswer (e.g. Firefox or Chrome), and log on to the web server using IP address 169.254.1.5. (Default Username/Password = admin/alphaadmin).
 +
 +
<br><br>
  
 
==Connection details==
 
==Connection details==
Line 50: Line 56:
  
 
===Analogue Intercom Stations===
 
===Analogue Intercom Stations===
There are [[Physical_number#AlphaCom_E7|36 physical ports]] for analog stations on the XE7. Station cables are terminated to these physical ports by means of [[Connection Kit ASLT/AGA/AE1/ATLB|plugable screw connectors]] on the backplane.
+
There are [[Physical_number#AlphaCom_E7|36 physical ports]] for analog stations on the XE7 server. Station cables are terminated to these physical ports by means of [[Connection Kit ASLT/AGA/AE1/ATLB|plugable screw connectors]] on the backplane.
  
 
===Audio Program Inputs ===
 
===Audio Program Inputs ===
Line 58: Line 64:
  
 
===Serial Ports===
 
===Serial Ports===
The serial ports with RS232 and RS422/RS485 interfaces are used for connecting to equipment using these protocols
 
 
[[File:Serial ports XE1 XE7.PNG|thumb|left|500px|XE7 Serial connections]]
 
<br style="clear:both;" />
 
 
====Serial Port 0====
 
9-Pin D-sub (RS232 Only)
 
:No additional settings necessary
 
 
====Serial Port 1====
 
RJ45 (RS232/422/485)
 
:Additional settings:
 
:'''RS232:'''
 
:* [[AMC-IP_-_AlphaCom_Processor_Board_(Red)#Switches_and_jumpers|Switch 8 on S601]] on the AMC-IP board must be set to OFF.
 
 
:'''RS422/485:'''
 
:* [[AMC-IP_-_AlphaCom_Processor_Board_(Red)#Switches_and_jumpers|Switch 8 on S601]] on the AMC-IP board must be set to ON.
 
:* Use the two jumpers on the backplane to select between RS422 and RS485
 
[[File:422 485 XE7.png|thumb|left|500px|RS422/485 selector for Serial Port 1 on the XE7 backplane]]
 
<br style="clear:both;" />
 
 
 
-----
 
 
[[File:Serial ports XE1.PNG|thumb|right|400px|XE7 Serial ports pinout]]
 
[[File:Serial ports XE1.PNG|thumb|right|400px|XE7 Serial ports pinout]]
 
Serial ports can be used for communication with external equipment. There are two serial ports:  
 
Serial ports can be used for communication with external equipment. There are two serial ports:  
 
* '''Serial Port 0''': R232 on an 9-Pin D-sub connector
 
* '''Serial Port 0''': R232 on an 9-Pin D-sub connector
* '''Serial Port 1''': RS232, RS422 or RS485 on an RJ45 connector
+
* '''Serial Port 1''': RS232, RS422 or RS485 on an RJ45 connector:
 
** '''RS232:''':  [[AMC-IP_-_AlphaCom_Processor_Board_(Black)#Switches_and_Jumpers|Switch 8 on S601]] on the AMC-IP board must be set to OFF (default).
 
** '''RS232:''':  [[AMC-IP_-_AlphaCom_Processor_Board_(Black)#Switches_and_Jumpers|Switch 8 on S601]] on the AMC-IP board must be set to OFF (default).
 
** '''RS422''': [[AMC-IP_-_AlphaCom_Processor_Board_(Black)#Switches_and_Jumpers|Switch 8 on S601]] on the AMC-IP board must be set to ON. Jumpers on backplane in '''RS422''' position.
 
** '''RS422''': [[AMC-IP_-_AlphaCom_Processor_Board_(Black)#Switches_and_Jumpers|Switch 8 on S601]] on the AMC-IP board must be set to ON. Jumpers on backplane in '''RS422''' position.
Line 91: Line 74:
  
  
 +
[[File:422 485 XE7.png|thumb|left|500px|Jumpers for RS422/485 selection for Serial Port 1 on the XE7 backplane]]
 +
<br style="clear:both;" />
  
To access the jumpers J1 and J2, remove the top lid of the XE1 server:
+
<br><br>
[[File:SerialPortJumpers XE1.png|thumb|left|300px|Jumpers J1 and J2 for selection of RS422 or RS485 for Serial Port 1]]
 
<br style="clear:both;" />
 
  
 
===Remote Control Inputs (RCI)===
 
===Remote Control Inputs (RCI)===
====Connections====
+
There are two remote control inputs available at the backplane of the XE7 server, called RCI 1 and RCI 2. The inputs are triggered by dry contacts. What actions to trigger when an input is activated is configured from AlphaPro in the [[Exchange_%26_System_(AlphaPro)#RCI|RCI table]]. For more information on usage and configuration, see [[RCI - Remote Contol Input]].
* There are two inputs for clean contacts on the [[RCI - Remote Contol Input|RCI connectors]] which can execute programmable functions.  
 
 
[[File:RCI XE7.png|left|thumb|500px|RCI inputs in an AlphaCom XE7]]
 
[[File:RCI XE7.png|left|thumb|500px|RCI inputs in an AlphaCom XE7]]
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
====Configuration====
+
<br><br>
In [[AlphaPro]] there is an [[Exchange_%26_System_%28AlphaPro%29#RCI|RCI table]], where the physical address of the input is entered, along with the desired actions. The physical address is given as [[device]] + pin-number.
 
  
The RCI table supports up to 140 inputs.
+
===Remote Control Outputs (RCO)===
* For internal RCIs in the AlphaCom XE7, the device address is 65-68, and the pin number is 1-6.
+
There are 12 Remote Control Outputs (RCO) available from the XE7 server.
* Internal pin number 8 is the [[Temperature Alarm|temperature alarm]]
+
* RCO 1 to 6 are operated by the [[ASLT]] or [[ATLB-12]] board in board postion 1
* Mappings for the internal RCI's are [[Autoload|autoloaded]]. Mappings for external RCI's (Slave modules, RIO's or IPARIO) must be manually programmed.
+
* RCO 7 to 12 are operated by the ASLT or ATLB-12 board in board postion 2
 
 
{| border="1"
 
! style="background:#ffdead;" width="150" |&nbsp;
 
! style="background:#ffdead;" width="80" |RCI Type
 
! style="background:#ffdead;" width="150" |Device/Station physical Number
 
! style="background:#ffdead;" width="100" |Pin Number
 
|-
 
| align=center | AlphaCom XE7 || align=center | Device || align=center | 65-68 || align=center | 1 - 6
 
|-
 
|}
 
 
 
====Example====
 
<big>Start fire alarm message and activate rotating lamp:</big>
 
[[File:RCI Conf Example1.PNG|left|800px]]
 
<br style="clear:both;" />
 
 
 
[[File:RCI Conf Example2.PNG|left|500px]]
 
<br style="clear:both;" />
 
 
 
AMG 1 3 - Alarm Message 3 (8193) to group 1 (84)
 
RCO 5 ON – Turn on the relay that controls the lamp
 
 
 
AMG 1 0 – Alarm Message OFF to group 1 (84)
 
RCO 5 OFF – Turn off the lamp
 
 
 
'''Note:''' Multiple commands are separated by semicolon ( ; )
 
  
===Remote Control Outputs (RCO)===
+
The outputs are designed to drive the relays on a [[MRBD]] relay board.
There are 12 RCOs that must be connected to optional [[MRBD]] relay boards, and can be programmed to execute functions such as door control.
 
  
{| border="1"
+
{{note|When the [[ATLB-12]] board is used, there will be [[ATLB in AlphaCom E7 - RCO's|only four RCOs]] available (not six) }}
! style="background:#ffdead;" width="250" |Device
 
! style="background:#ffdead;" width="50" |# of RCO's
 
! style="background:#ffdead;" width="300" |Comment
 
! style="background:#ffdead;" width="400" |Hardware required
 
|-
 
| align=center | AlphaCom XE7 || align=center | 12 || align=center | Need [[ASLT]] or [[ATLB-12]] in position 1 and 2 ''(x)'' || align=center | [[MRBD - Relay Board|MRBD relay board]]
 
|-
 
|}
 
''(x): When the [[ATLB-12]] board is used in [[ATLB in AlphaCom E7 - RCO's|AlphaCom XE7 only four RCOs]] are available''
 
  
====Connections====
+
Connection of MRBD Relay Board:
Alphacom XE7 RCO’s operate [[MRBD]] relays:
+
[[File:RCOinXE7.png|thumb|left|300px|MRBD board connected to RCO 1-6]]
[[File:RCOinXE7.png|thumb|left|300px]]
 
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
====Mapping====
+
The operation of the outputs are configured in the [[Event Handler]]. By default the outputs from the XE7 server are mapped to logical RCO number 1 - 12, and are controlled by the [[RCO - Set Remote Control Output|RCO command]].
The RCO's in an Alphacom XE7 must be mapped. This is done using AlphaPro. Navigate to Exchange & System -[[Exchange_%26_System_%28AlphaPro%29#RCO|RCO window]] where the logical RCO is assigned to a physical address.
 
  
The physical address is given as '''[[Device]]''' + '''Pin Number'''
+
Here are some examples:
 
+
* [[1-4h. Door Opening, Code Lock (practice)|Door opening and Code lock]]
[[File:XE7RCOMapping.png|thumb|left|500px]]
+
* [[2-2a. Call indication - Event Handler (practice)|Call indication]]
<br style="clear:both;" />
 
 
 
* RCO 1-138 are by default mapped to the internal RCOs in the AlphaCom, i.e. device 65 - pin 1 to device 65 - pin 138. For XE7 it is only the first 12 RCO's which would be default mapped to the correct physical address
 
* Mapping for all other RCO's must be configured manually
 
* The RCO's can be used freely within the system, e.g. an event on one station can operate an RCO located on a different station or device.
 
* The exchange always keeps track of the state of an output in case the device becomes faulty. When a faulty device becomes OK again, the exchange will restore the current RCO state.
 
  
 
==Factory Reset (coldstart)==
 
==Factory Reset (coldstart)==
Performing a '''cold start''' of the AMC-IP board will delete all previous programming, load factory default settings and set the IP-address to 169.254.1.5 with mask 255.255.0.0 on Eth0.
+
[[File:AMC-IP ColdStartButton.png|thumb|left|300px|Cold start button on AMC-IP board]]
 
 
[[File:AMC-IP ColdStartButton.png|thumb|left|200px|Cold start button on AMC-IP board]]
 
 
<br style="clear:both;" />
 
<br style="clear:both;" />
  
 
===Cold start procedure===
 
===Cold start procedure===
[[Image:Cold Start of AMC-IP.jpg|right|200px|thumb|Cold start to load default factory settings]]
+
This procedure will delete all previous programming, load factory default settings and set the IP-address to 169.254.1.5 with mask 255.255.0.0 on Eth0.
*Press the reset button on the power card briefly while keeping the cold start button pressed.
+
* Press and hold the cold start button of the AMC-IP board
*Keep the cold start button pressed at least 2 sec. after power on. The AMC status LED will blink green when the boot is ready.
+
* Press the reset button on the power card briefly
<br style="clear:both;" />
+
* Keep the cold start button pressed for at least 2 seconds more. The status LED of the AMC-IP board will flash green when the system is up and running.
  
=== Cold-start of AMC application only, keep IP setting ===
+
=== Cold-start of intercom application only, keep the IP settings ===
[[Image:Cold Start of AMC-IP.2.jpg|right|200px|thumb|Cold-start of AMC application]]
+
* Press the reset button on the power card briefly.
*Press the reset button on the power card briefly.
+
* After 10 seconds, press the "cold start" button on the AMC-IP board.
*After 10 seconds, press the cold start button on the AMC-IP board.
+
* Keep the "cold start" button pressed until the AMC-IP status LED is flashing green.
*Keep the cold start button pressed until the AMC status LED is blinking green.
 
<br style="clear:both;" />
 
 
 
===Modify Factory Default Settings===
 
After cold start the system is set up with a default program and is working without any further programming. To change or add to the default settings, the [[AlphaPro]] programming tool must be used.
 
  
 
===Other methods of factory default===
 
===Other methods of factory default===
Line 195: Line 125:
 
* '''From [[AlphaPro]]:''' Upload a default AlphaPro database to the exchange
 
* '''From [[AlphaPro]]:''' Upload a default AlphaPro database to the exchange
  
==Upgrade==
+
==Software upgrade==
===Software upgrade===
+
* It is highly recommended to [[AMC-IP software upgrade (Black AMC-IP board)|upgrade the software]] of the server to the latest version. Upgrade is done from the web interface of the server. This will ensure that the system has the latest features, bug fixes and security updates.
See [[AMC-IP software upgrade]]
 
 
 
===Hardware Upgrade===
 
See [[AlphaCom Exchange Upgrade]]
 
  
 
==Related articles==
 
==Related articles==

Latest revision as of 16:43, 4 March 2019

AlphaCom XE7 Audio Server with HD Voice

Highlights

  • Made to provide critical communication in any environment
  • Supports 552 stations, of which 36 stations can be analog intercom stations
  • SIM card based software configuration and disaster recovery
  • Fully compatible with any AlphaCom system

Mounting & Dimensions

The XE7 cabinet can be wall or shelf mounted, or mounted in a 19” rack. It has room for installation of one AMC-IP processor board and up to 6 feature boards. The server includes a power board and a cooling fan.

XE7 dimensions




Installation

  • Remove the front cover of the XE7 cabinet
  • Prepare the AMC-IP board with the STIC according to this article, then insert the AMC-IP board into board position 7.
OBS icon
  • Turn power off before inserting or removing any boards
  • Give the board a final firm push to make sure it goes all the way into position.


  • Insert the remaining feature boards (ASLT, ATLB-12 or AGA boards) in position 1 to 6. Normally you would start from board position 1 and upwards.
Board positions and physical numbers in AlphaCom XE7


  • Power up the XE7 server by connecting the output from the 24VAC transformer to the "24VAC In" connector.
    • Alternatively connect a 24VDC power source to the "24VDC In" connector.
  • Watch the LEDs of the AMC-IP board. The system uses approx. 70 seconds to start up. When running the green status LED of the AMC-IP board should be flashing.
  • Connect a laptop to Eth 0 port, open a web browser (e.g. Firefox or Chrome), and log on to the embedded web server using IP address 169.254.1.5. (Default Username/Password = admin/alphaadmin)
  • Upgrade the software of the server to the latest version. Upgrade is done from the web interface of the server. This will ensure that the system has the latest features, bug fixes and security updates.
  • Replace the front cover of the XE7 cabinet



Configuration

  • AlphaPro is the Windows application used for configuring the AlphaCom XE system. Configuration of user data, such as Directory Numbers, Direct Access Keys, Group Calls etc. is done from AlphaPro.
  • AlphaWeb is the embedded web server running on AlphaCom XE. The AlphaWeb server provides functions for system monitoring, system configuration, and system upgrade. Initial connection is done by connecting a laptop to Eth 0 port, open a web broswer (e.g. Firefox or Chrome), and log on to the web server using IP address 169.254.1.5. (Default Username/Password = admin/alphaadmin).



Connection details

Connections on the XE7 backplane


Power

The server is normally powered from the mains via a 24VAC transformer. Battery backup power can be connected to the 24VDC input plug.

Note icon For redundancy purposes it possible to connect both the 24VAC and the 24VDC at the same time. Under normal operation the server will use the 24VAC source. If the 24VAC drops out, the server will switch without any interruptions to the 24VDC source.


Network

The XE7 server has two RJ-45 ethernet ports for IP communication. Ethernet port 0 (Eth 0) is by default configured as a Management port, allowing connection to the embedded web server (AlphaWeb) and connection of the PC configuration tool AlphaPro. Default IP addresses:

  • Eth0 has IP address 169.254.1.5
  • Eth1 gets IP address from DHCP by default

Analogue Intercom Stations

There are 36 physical ports for analog stations on the XE7 server. Station cables are terminated to these physical ports by means of plugable screw connectors on the backplane.

Audio Program Inputs

Physical number 5 and 6 on the first ASLT line board are by default enabled for audio program distribution. If more program inputs are required, one can use the AGA board (6 programs per board), or use the TKIE-2 kit as Audio Program interface.

If you want to use the physical ports 5 & 6 for regular analog stations instead, see article Physical number 5 and 6 (AlphaCom E7)

Serial Ports

XE7 Serial ports pinout

Serial ports can be used for communication with external equipment. There are two serial ports:

  • Serial Port 0: R232 on an 9-Pin D-sub connector
  • Serial Port 1: RS232, RS422 or RS485 on an RJ45 connector:
    • RS232:: Switch 8 on S601 on the AMC-IP board must be set to OFF (default).
    • RS422: Switch 8 on S601 on the AMC-IP board must be set to ON. Jumpers on backplane in RS422 position.
    • RS485: Switch 8 on S601 on the AMC-IP board must be set to ON. Jumpers on backplane in RS485 position.


Jumpers for RS422/485 selection for Serial Port 1 on the XE7 backplane




Remote Control Inputs (RCI)

There are two remote control inputs available at the backplane of the XE7 server, called RCI 1 and RCI 2. The inputs are triggered by dry contacts. What actions to trigger when an input is activated is configured from AlphaPro in the RCI table. For more information on usage and configuration, see RCI - Remote Contol Input.

RCI inputs in an AlphaCom XE7




Remote Control Outputs (RCO)

There are 12 Remote Control Outputs (RCO) available from the XE7 server.

  • RCO 1 to 6 are operated by the ASLT or ATLB-12 board in board postion 1
  • RCO 7 to 12 are operated by the ASLT or ATLB-12 board in board postion 2

The outputs are designed to drive the relays on a MRBD relay board.

Note icon When the ATLB-12 board is used, there will be only four RCOs available (not six)


Connection of MRBD Relay Board:

MRBD board connected to RCO 1-6


The operation of the outputs are configured in the Event Handler. By default the outputs from the XE7 server are mapped to logical RCO number 1 - 12, and are controlled by the RCO command.

Here are some examples:

Factory Reset (coldstart)

Cold start button on AMC-IP board


Cold start procedure

This procedure will delete all previous programming, load factory default settings and set the IP-address to 169.254.1.5 with mask 255.255.0.0 on Eth0.

  • Press and hold the cold start button of the AMC-IP board
  • Press the reset button on the power card briefly
  • Keep the cold start button pressed for at least 2 seconds more. The status LED of the AMC-IP board will flash green when the system is up and running.

Cold-start of intercom application only, keep the IP settings

  • Press the reset button on the power card briefly.
  • After 10 seconds, press the "cold start" button on the AMC-IP board.
  • Keep the "cold start" button pressed until the AMC-IP status LED is flashing green.

Other methods of factory default

A factory default can also be achieved in other ways:

  • From AlphaWeb: System Maintenance -> System Recovery -> Load Factory Defaults
  • From AlphaPro: Upload a default AlphaPro database to the exchange

Software upgrade

  • It is highly recommended to upgrade the software of the server to the latest version. Upgrade is done from the web interface of the server. This will ensure that the system has the latest features, bug fixes and security updates.

Related articles