Search results
Create the page "Note" on this wiki! See also the search results found.
- # Do a "Clean & Factory Reset" from the web interface. Note that licenses are deleted so you need to insert them again {{Note| During this procedure any license will be deleted so you need to insert th503 bytes (73 words) - 14:16, 8 October 2019
- {{note| {{note| AlphaPro v12 is also supported using Windows 11}}930 bytes (133 words) - 15:53, 4 April 2024
- '''Note 1:''' Block state will always be cleared after reset. <br> '''Note 2:''' Only station events kicked by DIP protocoll are blocked. Events from1 KB (214 words) - 16:11, 3 October 2019
- {{Note|If there are uploaded messages, download and store these.}} {{Note|Upload audio messages if any}}856 bytes (121 words) - 10:19, 25 September 2020
- {{note|If PoE is used, the station must be installed using a shielded Ethernet cab {{note|If an external power supply is being used, please make sure the power suppl3 KB (424 words) - 15:43, 8 September 2023
- {{Note|AMC 9: The script uses approx. 3 seconds to empty a group of 100 members. 1 {{Note|AMC 11: The script uses approx. 2 seconds to empty a group of 552 members}}873 bytes (122 words) - 11:35, 8 July 2022
- ''Note: A change of the IP address is made via the web interface of the CP-CAM.'' # Note the switch position and then turn both switches to "OFF".959 bytes (156 words) - 15:10, 5 February 2018
- Note the limitation of the Total Recall recorder are Mono recordings in g.711u o Note that the expected logging of the calls is by the Display Name only. Ensure1 KB (176 words) - 03:50, 4 May 2023
- '''NOTE: Since AlphaPro version 11.5.x.x there is no support for serial communicati302 bytes (45 words) - 10:59, 24 October 2023
- {{note|Triggered only when the mail is received, i.e. "When Change To" goes ON }}326 bytes (48 words) - 09:46, 4 October 2019
- {{note|Triggered only when the mail is received, i.e. "When Change To" goes ON }}333 bytes (48 words) - 09:46, 4 October 2019
- {{note|This article is applicable for the [[School IP Intercom - 1402001000]].}} {{Note| This LED behaviour only applies in ICX-AlphaCom mode}}1 KB (168 words) - 17:25, 31 January 2023
- == Note template == <nowiki>{{Note|Lorem ipsum dolor sit amet, consetetur sadipscing elitr, sed. }}</nowiki>4 KB (614 words) - 14:06, 13 September 2019
- *789 + M + M + M: Show IP address of Eth0 and Eth1 (see note below) Note: IP address of Eth0/Eth1 is the ''configured'' IP addresses, as used by Int1 KB (175 words) - 09:29, 11 May 2022
- {{note|[[Advanced Configuration Mode (Edge)|Advanced Configuration Mode]] must be {{Note|VoIP port range is configurable from firmware 2.7 (INCA) and 4.7 (Turbine)2 KB (191 words) - 16:22, 12 September 2023
- {{Note|This option is available for the [[IP Desk Master -V2 w/handset|IP Desk Mas {{Note|To access the '''Language''' settings, you must enable [[Advanced Configura1 KB (212 words) - 12:06, 19 May 2021
- {{Note|This option is available for the [[IP Desk Master -V2 w/handset|IP Desk Mas {{Note|To access the '''Language''' settings, you must enable [[Advanced Configura1 KB (210 words) - 12:00, 19 May 2021
- The AlphaCom requires the presence of the appropriate API/OPC license. Note that every AlphaCom in an AlphaNet requires such a license. ...llation instructions for [[OPC Classic for AlphaCom - Installation]]{{Note|Note: At this time, there is a buffer overflow bug in SiPass that will crash the2 KB (310 words) - 09:01, 16 August 2022
- {{note|This is not a 1:1 cable }}423 bytes (57 words) - 09:15, 29 September 2021
- ** Note that in software AMC 11.2.3.9 or earlier the inputs were reported as DAK 1 ** Note that in software AMC 11.2.3.9 or earlier the outputs were numbered 1 - 7. I3 KB (461 words) - 11:21, 23 June 2023