|
|
| (128 intermediate revisions by 3 users not shown) |
| Line 1: |
Line 1: |
| − | IP Audio Remote I/O Unit
| + | {{Obsolete}} |
| − | [[File:IP-ARIO.PNG|thumb|400px]] | + | {{AI}} |
| − | The IP Audio Remote I/O (IP-ARIO) unit has a wide set of hardware functions and can be used as a PA Interface, a Radio Interface, or as a pure IP-based Remote I/O Unit.
| + | [[File:IP-ARIO.PNG|thumb|400px|IP-ARIO, Item Number: 1008095100]] |
| | | | |
| − | =Installation=
| + | This product is discontinued. |
| − | The table below is an overview of the main connections involved when installing the IP-ARIO unit.
| + | Replacement depends on type of use (see [[Kits - Comparison chart]]): |
| − | {| border="1"
| + | * For PA integration, use [[TKIS-2]] |
| − | |-
| + | * For Mobile Radio Integration use [[TKIE-2]] |
| − | | LAN || 10/100 Mbps RJ45 port for LAN (uplink) connection. Supports PoE (802.3af). Draws power from either spare line or signal line.
| + | * For I/O, use [[IP-LCM]] |
| − | |-
| |
| − | | AUX || 10/100 Mbps RJ45 port for auxiliary equipment such as PC and IP camera.
| |
| − | |-
| |
| − | | RS232 || RJ45 port (pinout: 3=TX, 4&5=GND, 6=RX)
| |
| − | |-
| |
| − | | PA Interface || Dual Balanced 600 Ohm 0dB audio out (adjustable 0 to -10 dB)
| |
| − | |-
| |
| − | | Radio Interface || Single 600 Ohm 0dB audio in/out (adjustable 0 to -10 dB)
| |
| − | |-
| |
| − | | Digital Inputs || 8 inputs (Input 1 and 2 is referred to GND, input 3 to 8 is shorting or referred to GND)
| |
| − | |-
| |
| − | | Digital Outputs || 8 relay outputs (Output 1 - 4 is closing contact, output 5 - 8 is change-over contact)
| |
| − | |-
| |
| − | | Local Power || Pluggable screw terminal, 19-27 VDC Idle 4W, max. 8W
| |
| − | |-
| |
| − | |}
| |
| | | | |
| − | ==Power Supply==
| + | The IP Audio Remote I/O ('''IP-ARIO''') unit has a wide set of hardware functions. It can be used as: |
| − | The IP-ARIO unit supports Power over Ethernet (PoE,IEEE 802.3af) where power can be drawn from either the spare or signal line. If PoE is not available, the IP-ARIO | + | *PA Interface over IP |
| − | unit can be connected to a local power supply of 24 VDC. | + | *Radio Interface over IP |
| | + | *Remote I/O unit over IP |
| | + | *Remote AlphaCom RS232 port over IP |
| | | | |
| − | ==Network Connection== | + | == Requirements == |
| − | [[File:IP-ARIOrear.PNG|thumb|align=center|400px|IP-ARIO rear view]]
| + | '''Software:''' |
| − | There are three RJ45 ports at the rear of the IP-ARIO unit:
| + | * AMC-IP version 11.2.3.1 or newer |
| − | * '''LAN''' port is for connecting to the network and the AlphaCom server/exchange.
| + | * AlphaPro Version 11.2.3.0 or newer |
| − | * '''AUX''' port is for connecting to auxiliary equipment such as a PC. | |
| − | * '''RS 232''' port is for remote signalling | |
| | | | |
| − | <br style="clear:both;" />
| + | '''Server:''' |
| | + | * AlphaCom server is required |
| | + | * The IP-ARIO is not supported in Pulse or SIP mode. |
| | | | |
| − | =Configuration using AlphaPro= | + | == License Requirements == |
| | + | * An [[Licenses#IP-ARIO_Audio_License|IP-ARIO Audio License]] is required in the AlphaCom when the audio part of IP-ARIO is used, i.e. when the IP-ARIO is used as PA interface or as a Mobile Radio interface. |
| | + | * If only the I/O part of the IP-ARIO is used, no license is required. The AlphaCom will automatically recognize the unit as an IP-ARIO and allow it to register without a license. |
| | | | |
| − | ==Mandatory Configuration== | + | == Connections == |
| − | [[File:IP-ARIOConfig1.PNG|thumb|400px]] | + | * [[IP-ARIO Connections|IP-ARIO connections]] |
| − | Open the AlphaPro programming tool on your PC and click the '''Users & Stations''' icon. <br/>
| |
| − | [[File:AlphaPro directory icon.jpg]]
| |
| − | <br/>
| |
| − | IP-ARIO should be configured as a CCoIP station: | |
| − | * For '''Station Type''', select '''Sub Station'''
| |
| − | * Check the '''CCoIP Station''' box
| |
| − | * Check the '''Reg. w/ Directory Number''' box
| |
| | | | |
| − | <br style="clear:both;" />
| + | ==Configuration== |
| | + | * [[IP-ARIO Configuration]] |
| | | | |
| − | ==Configuring PA interface== | + | == Advanced Network Settings == |
| − | [[File:IP-ARIOConfig2.PNG|thumb|400px]] | + | * [[VLAN Settings (Devices)]] |
| − | Under '''Users & Stations''' click the '''Station Type''' tab.
| + | * [[IEEE 802.1X|Network Access Control (802.1X)]] |
| − | Under '''IP-ARIO''', set the following flags:
| |
| − | * Check the '''XLR PA Monitoring''' box
| |
| − | * Check the '''2 Amplifiers''' box
| |
| − | * Check the '''Request Audio License''' box
| |
| | | | |
| − | <br style="clear:both;" />
| + | == Restore Factory Defaults and Software Upgrade == |
| | + | * [[IP-ARIO Restore Factory Defaults|Reset to factory settings]] |
| | + | * [[INCA Station Software upgrade|Upgrade via the station web interface]] |
| | + | * [[IMT - Discover & Upgrade|Upgrade using the IMT tool]] |
| | + | * [[:Category:INCA Release notes|Software Release Notes]] |
| | | | |
| − | ==Configuring Radio Interface== | + | == Dimensions == |
| − | For this configuration, the IP-ARIO unit has to be defined as Default Speaker in the Simplex Conference used for radio listening.
| + | *[[IP_ARIO Dimensions & Mounting Instructions|Dimensions]] |
| − | * Click the '''Simplex Conferences''' icon.
| |
| − | [[File:AlphaPro SX conference icon.jpg]]
| |
| − | * Select a Conference and click '''Change''' | |
| − | [[File:IP-ARIOConfig3.PNG|thumb|right|300px|Define IPARIO as Default Speaker in the conference]] | |
| − | * For '''Default Member''', select the IP ARIO unit
| |
| − | * Check the '''Default Member is Default Speaker''' box
| |
| | | | |
| − | ==Configuring Inputs & Outputs== | + | == Accessories == |
| − | [[File:IP-ARIOConfig4.PNG|thumb|400px]] | + | * [[IP ARIO Dimensions & Mounting Instructions|Mounting brackets]] |
| − | Remote Control Inputs & Outputs are configured under the Exchange & System menu. <br/>
| |
| − | [[File:Exchange icon.jpg]] <br/>
| |
| − | For Remote Control Inputs:
| |
| − | * Click '''RCI'''
| |
| − | * Click '''Change''' to set '''RCI Type''' to '''Station'''
| |
| − | * Enter the IP-ARIO '''station number''' in the '''Station''' field
| |
| − | <br style="clear:both;" />
| |
| | | | |
| − | [[File:IP-ARIOConfig5.PNG|thumb|400px]]
| + | == Software Requirements == |
| − | For Remote Control Outputs:
| + | This station is fully supported as form AlphaCom version 11.2.3.1 |
| − | * Click '''RCO'''
| |
| − | * Click '''Change''' to set '''RCO Type''' to '''Station'''
| |
| − | * Enter the IP-ARIO '''station number''' in the '''Station''' field
| |
| − | <br style="clear:both;" />
| |
| | | | |
| − | ==Configuring Remote Serial Port== | + | == Related information == |
| − | [[File:IP-ARIOConfig6.PNG|thumb|400px]] | + | * [http://www.zenitel.com/product/ip-ario Additional Documentation on Zenitel.com] |
| − | Click the '''Exchange & System''' icon and click '''Serial Ports'''. <br/>
| |
| − | [[File:Exchange icon.jpg]] <br/>
| |
| − | * Select one of the '''EDIO''' drivers and click '''Change'''
| |
| − | <br style="clear:both;" />
| |
| − | [[File:IP-ARIOConfig7.PNG|thumb|400px]]
| |
| − | * Check the '''Enabled''' box
| |
| − | * Set '''Port Type''' to '''IP-PARIO'''
| |
| − | * Enter the '''physical number''' of the unit in the '''Station''' field
| |
| − | * Enter the '''port number''' in the '''Port''' field
| |
| − | ** The port number (e.g. 4000) must be defined and opened under '''Filters''' in AlphaWeb
| |
| − | * Click '''OK'''
| |
| | | | |
| − | <br style="clear:both;" />
| |
| | | | |
| − | =Configuration using Web Browser=
| + | [[Category: INCA Stations]] |
| − | ==IP-ARIO Web Interface==
| |
| − | The IP-ARIO unit features an embedded web server, which allows users to log in via a standard web browser. At commissioning, the IP-ARIO unit needs to be configured to enable it to subscribe to an AlphaCom server/exchange. To do this, your PC and the IP-ARIO unit have to be connected together via a PoE switch using network cables:
| |
| − | * Connect the PC to the PoE switch
| |
| − | * Connect the '''LAN''' port on the IP-ARIO unit to the PoE switch
| |
| − | <br/>
| |
| − | The factory default IP address of the IP-ARIO unit is '''169.254.1.100'''. In order for your PC to communicate with the unit it is necessary to change its '''Internet Protocol Properties''' to use an IP address that is in the same range as 169.254.1.100, e.g. 169.254.1.1 with subnet mask 255.255.0.0.
| |
| − | <br/>
| |
| − | After the IP properties have been changed, access the IP-ARIO unit by logging into the web interface using a standard web browser:
| |
| − | 1. Open a web browser on your PC <br/>
| |
| − | 2. In the browser’s address bar, type '''http://169.254.1.100''' and press the ENTER key
| |
| − | * The station Login page is displayed.
| |
| − | [[File:IP-ARIOConfig8.PNG]] <br/>
| |
| − | To log into the IP-ARIO unit: <br/>
| |
| − | 1. Click '''Login''' <br/>
| |
| − | 2. Enter the default user name:
| |
| − | '''admin'''
| |
| − | 3. Enter the default password:
| |
| − | '''alphaadmin'''
| |
| − | <br/>
| |
| − | The '''Station Info''' page will now be displayed, showing the IP-ARIO unit configuration. Use the menu bar at the top of each page to browse through the various pages.
| |
| − | | |
| − | ==CCoIP Configuration==
| |
| − | * Click '''CCoIP Configuration''' to access the page for configuring IP parameters.
| |
| − | [[File:IP-ARIOConfig9.PNG|thumb|400px]]
| |
| − | '''Registration Settings''' <br/>
| |
| − | * Enter the IP address of the AlphaCom server/exchange in which the IP-ARIO unit is to be a subscriber in the '''AlphaCom IP-address''' field.
| |
| − | * Enter the directory number of the IP-ARIO unit in the '''Request Directory Number''' field.
| |
| − | ** If a directory number is not entered, the IP-ARIO unit will register with its MAC address. The MAC address is found on the '''Station Info''' page and needs to be entered into the AlphaPro programming tool.
| |
| − | | |
| − | '''CCoIP Station – IP Settings''' <br/>
| |
| − | * '''DHCP''' – Use this option if the IP-ARIO unit shall receive IP Settings from a DHCP server.
| |
| − | * '''Static IP''' – Use this option if the IP-ARIO unit shall use a static IP address. Enter the IP address, subnet mask and gateway address.
| |
| − | * Click '''Save configuration''' followed by '''Apply''' to apply the new configuration settings.
| |
| − | | |
| − | <br style="clear:both;" />
| |
| − | | |
| − | =Factory Default IP Settings=
| |
| − | [[File:IP-ARIOConfig10.PNG|thumb|400px|Front view]]
| |
| − | To configure the IP-ARIO unit with Factory Default IP Settings do the following: <br/>
| |
| − | 1. Disconnect power to the unit. <br/>
| |
| − | 2. Reconnect power and within 5 seconds, use a pin to press and hold the pinhole Reset button (on the frontright of the unit). <br/>
| |
| − | 3. Keep the Reset button pressed untill the CALL LED emits 3 slow flashes followed by 3 fast flashes as confirmation that the unit is reset.
| |
| − | * This takes approximately 25 seconds. <br/>
| |
| − | 4. Release the Reset button. <br/>
| |
| − | The unit’s IP settings will now be reset to the factory default values with IP address 169.254.1.100.
| |
| − | <br style="clear:both;" />
| |
| − | | |
| − | =License Requirements=
| |
| − | An [[Licenses#IP-ARIO_Audio_License|IP-ARIO Audio License]] is required when the audio part of IP-ARIO is used, i.e. PA and Radio. To install the license, open AlphaWeb on AlphaCom by entering its IP address in a browser:
| |
| − | * Select '''System Configuration > Licensing'''
| |
| − | * Click '''Insert new License Key'''
| |
| − | [[File:IP-ARIOConfig11.PNG|tumb|400px]] | |
| − | * Enter the key string in the '''Input License Key''' field
| |
| − | * Click '''Insert Key''' to install the license.
| |
| − | | |
| − | ''If only the I/O part of the IP-ARIO is used, no license is required. The AlphaCom will automatically recognize the unit as an IP-ARIO and ''
| |
| − | ''allow it to register without a license.''
| |
| − | | |
| − | ==Software Requirements==
| |
| − | '''AlphaCom XE''': AMC-IP version 11.2.3.1 or higher <br/>
| |
| − | '''AlphaPro''': Version 11.2.3.0 or higher
| |
| − | | |
| − | ==Local Status Monitoring==
| |
| − | The Local Status Monitoring (LSM) feature can be started anytime after booting up the IP-ARIO unit. LSM will show the status on the following monitored items:
| |
| − | * PA 1 and PA 2 for 20 kHz speaker monitoring
| |
| − | * XLR 1 and XLR 2 for XLR connectors connection status
| |
| − | * RCI 1 to RCI 8 showing active or non-active RCI inputs
| |
| − | * RCO 1 to RCO 8 showing active or non-active RCO outputs
| |
| − | <br/>
| |
| − | LSM is started by using a pin to press the pinhole Reset button located on the front-right of the unit. All LEDs at the front of the unit will be lit as long as the Reset button is pressed (as visual verification of the LED status). When the Reset button is released, LSM continues and the LEDs will show the following:
| |
| − | * '''CALL''' LED fast flashing to indicate that the LSM feature is active.
| |
| − | * '''STATUS''' LED indicates monitored group (3 groups)
| |
| − | ** PA/XLR (green off, red off)
| |
| − | ** RCI (green on, red off)
| |
| − | ** RCO (green off, red on)
| |
| − | * '''RADIO''' LED indicates monitored item within group, mix of LEDs on, off, slow and fast flashing.
| |
| − | * '''ERROR''' LED indicates status of monitored item, on if fail or active, off if OK or non-active.
| |
| − | <br/>
| |
| − | PA/XLR needs approximately 10 seconds to be updated if the status changes, i.e. if the XLR connector is disconnected and then reconnected. <br/>
| |
| − | RCI and RCO will show instant updating if the status changes, i.e. if RCI 1 changes status, this will be immediately indicated on the '''ERROR''' LED if RCI 1 is monitored. <br/>
| |
| − | Each time the Reset button is toggled, the status of the next LSM item is indicated on the '''ERROR LED'''. <br/>
| |
| − | The LSM can be terminated at any time by pressing and holding the Reset button for at least 2 seconds. LSM will auto-terminate 2 minutes after the last Reset button
| |
| − | activity. <br/>
| |
| − | The table below shows the relation between the current status of the monitored item and the different LED indicators.
| |
| − | <br/>
| |
| − | <br/>
| |
| − | | |
| − | {| border="1"
| |
| − | |-
| |
| − | !colspan="9" align="center" style="background:#ffcb00;"|Local Status Monitoring
| |
| − | |-
| |
| − | !colspan="2" style="background:#ffcb00;"| ||colspan="7" align="center" style="background:#ffcb00;"|Front LEDs
| |
| − | |-
| |
| − | !colspan="2" style="background:#ffcb00;"| ||align="center" style="background:#ffcb00;"|CALL||colspan="2" align="center" style="background:#ffcb00;"|STATUS||colspan="2" align="center" style="background:#ffcb00;"|RADIO||colspan="2" align="center" style="background:#ffcb00;"|ERROR
| |
| − | |-
| |
| − | !style="background:#ffcb00;" width="120pt"|Toggle #
| |
| − | !style="background:#ffcb00;" width="120pt"|Monitored Item
| |
| − | !style="background:#ffcb00;" width="120pt"|Green
| |
| − | !style="background:#ffcb00;" width="120pt"|Color
| |
| − | !style="background:#ffcb00;" width="120pt"|Indication
| |
| − | !style="background:#ffcb00;" width="120pt"|Color
| |
| − | !style="background:#ffcb00;" width="120pt"|Indication
| |
| − | !style="background:#ffcb00;" width="120pt"|Red:ON
| |
| − | !style="background:#ffcb00;" width="120pt"|Red:OFF
| |
| − | |-
| |
| − | !| 0
| |
| − | !| PA 1
| |
| − | !| FAST
| |
| − | !| NONE
| |
| − | !| OFF
| |
| − | !| GREEN
| |
| − | !| ON
| |
| − | !| Fail
| |
| − | !| OK
| |
| − | |-
| |
| − | !| 1
| |
| − | !| PA 2
| |
| − | !| FAST
| |
| − | !| NONE
| |
| − | !| OFF
| |
| − | !| GREEN
| |
| − | !| SLOW
| |
| − | !| Fail
| |
| − | !| OK
| |
| − | |-
| |
| − | !| 2
| |
| − | !| XLR 1
| |
| − | !| FAST
| |
| − | !| NONE
| |
| − | !| OFF
| |
| − | !| RED
| |
| − | !| ON
| |
| − | !| Fail
| |
| − | !| OK
| |
| − | |-
| |
| − | !| 3
| |
| − | !| XLR 2
| |
| − | !| FAST
| |
| − | !| NONE
| |
| − | !| OFF
| |
| − | !| RED
| |
| − | !| SLOW
| |
| − | !| Fail
| |
| − | !| OK
| |
| − | |-
| |
| − | !| 4
| |
| − | !| RCI 1
| |
| − | !| FAST
| |
| − | !| GREEN
| |
| − | !| ON
| |
| − | !| GREEN
| |
| − | !| ON
| |
| − | !| Active
| |
| − | !| Non-ACTIVE
| |
| − | |-
| |
| − | !| 5
| |
| − | !| RCI 2
| |
| − | !| FAST
| |
| − | !| GREEN
| |
| − | !| ON
| |
| − | !| GREEN
| |
| − | !| SLOW
| |
| − | !| Active
| |
| − | !| Non-ACTIVE
| |
| − | |-
| |
| − | !| 6
| |
| − | !| RCI 3
| |
| − | !| FAST
| |
| − | !| GREEN
| |
| − | !| ON
| |
| − | !| GREEN
| |
| − | !| FAST
| |
| − | !| Active
| |
| − | !| Non-ACTIVE
| |
| − | |-
| |
| − | !| 7
| |
| − | !| RCI 4
| |
| − | !| FAST
| |
| − | !| GREEN
| |
| − | !| ON
| |
| − | !| RED
| |
| − | !| ON
| |
| − | !| Active
| |
| − | !| Non-ACTIVE
| |
| − | |-
| |
| − | !| 8
| |
| − | !| RCI 5
| |
| − | !| FAST
| |
| − | !| GREEN
| |
| − | !| ON
| |
| − | !| RED
| |
| − | !| SLOW
| |
| − | !| Active
| |
| − | !| Non-ACTIVE
| |
| − | |-
| |
| − | !| 9
| |
| − | !| RCI 6
| |
| − | !| FAST
| |
| − | !| GREEN
| |
| − | !| ON
| |
| − | !| RED
| |
| − | !| FAST
| |
| − | !| Active
| |
| − | !| Non-ACTIVE
| |
| − | |-
| |
| − | !| 10
| |
| − | !| RCI 7
| |
| − | !| FAST
| |
| − | !| GREEN
| |
| − | !| ON
| |
| − | !| YELLOW
| |
| − | !| ON
| |
| − | !| Active
| |
| − | !| Non-ACTIVE
| |
| − | |-
| |
| − | !| 11
| |
| − | !| RCI 8
| |
| − | !| FAST
| |
| − | !| GREEN
| |
| − | !| ON
| |
| − | !| YELLOW
| |
| − | !| SLOW
| |
| − | !| Active
| |
| − | !| Non-ACTIVE
| |
| − | |-
| |
| − | !| 12
| |
| − | !| RCO 1
| |
| − | !| FAST
| |
| − | !| RED
| |
| − | !| ON
| |
| − | !| GREEN
| |
| − | !| ON
| |
| − | !| Active
| |
| − | !| Non-ACTIVE
| |
| − | |-
| |
| − | !| 13
| |
| − | !| RCO 2
| |
| − | !| FAST
| |
| − | !| RED
| |
| − | !| ON
| |
| − | !| GREEN
| |
| − | !| SLOW
| |
| − | !| Active
| |
| − | !| Non-ACTIVE
| |
| − | |-
| |
| − | !| 14
| |
| − | !| RCO 3
| |
| − | !| FAST
| |
| − | !| RED
| |
| − | !| ON
| |
| − | !| GREEN
| |
| − | !| FAST
| |
| − | !| Active
| |
| − | !| Non-ACTIVE
| |
| − | |-
| |
| − | !| 15
| |
| − | !| RCO 4
| |
| − | !| FAST
| |
| − | !| RED
| |
| − | !| ON
| |
| − | !| RED
| |
| − | !| ON
| |
| − | !| Active
| |
| − | !| Non-ACTIVE
| |
| − | |-
| |
| − | !| 16
| |
| − | !| RCO 5
| |
| − | !| FAST
| |
| − | !| RED
| |
| − | !| ON
| |
| − | !| RED
| |
| − | !| SLOW
| |
| − | !| Active
| |
| − | !| Non-ACTIVE
| |
| − | |-
| |
| − | !| 17
| |
| − | !| RCO 6
| |
| − | !| FAST
| |
| − | !| RED
| |
| − | !| ON
| |
| − | !| RED
| |
| − | !| FAST
| |
| − | !| Active
| |
| − | !| Non-ACTIVE
| |
| − | |-
| |
| − | !| 18
| |
| − | !| RCO 7
| |
| − | !| FAST
| |
| − | !| RED
| |
| − | !| ON
| |
| − | !| YELLOW
| |
| − | !| ON
| |
| − | !| Active
| |
| − | !| Non-ACTIVE
| |
| − | |-
| |
| − | !| 19
| |
| − | !| RCO 8
| |
| − | !| FAST
| |
| − | !| RED
| |
| − | !| ON
| |
| − | !| YELLOW
| |
| − | !| SLOW
| |
| − | !| Active
| |
| − | !| Non-ACTIVE
| |
| − | |-
| |
| − | |}
| |
| − | | |
| − | '''SLOW''' means slow flashing at 500 ms on and 500 ms off. <br/>
| |
| − | '''FAST''' means fast flashing at 250 ms on and 250 ms off. <br/>
| |
| | | | |
| | =Related Articles= | | =Related Articles= |
| − | * [[PA Failure State System]] <br/> | + | * [[PA Failure State System]] |
| | + | * [[Mototrbo and AlphaCom interfacing]] |
| | + | * [[IP station as program]] |
| | | | |
| | + | [[Category: Discontinued Stations]] |
| | [[Category: IP-ARIO]] | | [[Category: IP-ARIO]] |
| − | | + | [[Category: Public Address - Interfaces]] |
| − | [[Category: Public Address]] | + | [[Category: Additional equipment]] |
