Actions

ECPIR-3P: Difference between revisions

From Zenitel Wiki
No edit summary
 
(21 intermediate revisions by 4 users not shown)
Line 1: Line 1:
{{APS}}[[file:ECPIR-3PFront.PNG|right|400px|thumb|Exigo call panel (102 3200 033)]]
{{ACEIS}}[[file:ECPIR-3P-newZ.png|200px|thumb|Exigo call panel (1023200033)|alt=]]
== Getting started ==
==Getting started==
* [[ECPIR Connections|Connecting your Turbine Intercom station]]
* [[Starting Up Turbine Station|Starting up]]
* [[Starting Up Turbine Station|Starting up]]


== Configuration ==
==Configuration==
The station can operate in three different modes, depending on what kind of server the station should register to. Choose one of the links below according to what mode you need to configure.
The device can operate in [[Main Settings (IP Stations)|different modes]]. Set the mode according to the server the station should register to.
* AlphaCom mode
* [[IP Station Configuration - ICX-AlphaCom mode|ICX-AlphaCom mode]]
** [[Turbine Configuration - AlphaCom mode|Basic configuration]]
* [[Adding station to existing system (Edge)|Edge mode]]
** [[EBMDR-8 - Configuration|Configuration for Expansion Module EBMDB-8]]
* [[SIP Intercom - Web Interface|SIP mode]]
* [[SIP Intercom Configuration|SIP mode]] (*)
{{note|To use this device with [[:Category:Zenitel Connect Pro|Zenitel Connect Pro]] it must be factory defaulted. The device configuration is done from the Zenitel Connect Pro server.}}
** [[Direct Access Key & Ringlist Settings (Pulse)]]
* [[IP Station Configuration - Pulse mode|Pulse mode]] (*)
** [[Direct Access Key & Ringlist Settings SIP)]]


:(*) SIP and Pulse mode is fully supported as from firmware version 4.7.
Station specific configuration for the ECPIR:
* [[EBMDR-8 - Configuration|Configuration for Expansion Module EBMDB-8]]
* [[Direct Access Key & Ringlist Settings (Edge)]]
* [[Direct Access Key & Ringlist Settings (SIP)]]


== Restore Factory Defaults and Software Upgrade ==
==Restore Factory Defaults and Software Upgrade==
* [[TFIE Restore Factory Defaults|Restore Factory Defaults]]
* [[Turbine Software Upgrade|Upgrade via the station web interface]]
* [[VS-IMT Upgrade Stations|Upgrade using the IMT tool]]
* [[Automatic Software Upgrade|Automatic Software Upgrade (SIP mode only)]]


== Connectors, Indicators and Dimensions ==
*[[TFIE Restore Factory Defaults|Restore Factory Defaults]]
* [[Turbine Extended Board Connectors|Board Connections]]
*[[Turbine Software Upgrade|Upgrade via the station web interface]]
*[[IMT - Discover & Upgrade|Upgrade using the IMT tool]]
*[[Automatic Software Upgrade|Automatic Software Upgrade (SIP mode only)]]
* [[:Category:IMX28 Release notes|Software Release Notes]]
 
==Connectors, Indicators and Dimensions==
* [[Turbine Extended series board connectors|Device Connections]]
* [[TFIE Indication LEDs|Station Indication LEDs]]
* [[TFIE Indication LEDs|Station Indication LEDs]]
* [[ECPIR Dimensions & Mounting Instructions|Dimensions]]
* [[ECPIR Dimensions & Mounting Instructions|Dimensions]]


== Accessories ==
==Accessories==


{|{{SimpleTable}}
{| {{SimpleTable}} border="0"
|-
|-
|[[File:1023201008.png|100px|link=EBMDR-8]]
|style="text-align: center; vertical-align: top;"|[[File:EBMDR-8-newZ.png|100px|link=EBMDR-8]]
|[[File:3005020033.PNG|100px|link=MB-30G]]
|style="text-align: center; vertical-align: top;"|[[File:3005020033.PNG|100px|link=MB-30G]]
|[[File:1023533011.PNG|100px|link=EMMAR-1H]]
|style="text-align: center; vertical-align: top;"|[[File:1023533012.png|100px|link=PAM1H]]
|[[File:1023595010.PNG|80px|link=EMBR-1]]
|style="text-align: center; vertical-align: top;"|[[File:1023595010.PNG|80px|link=EMBR-1]]
|[[File:1023595020.PNG|140px|link=EMBR-2]]
|style="text-align: center; vertical-align: top;"|[[File:1023595020.PNG|140px|link=EMBR-2]]
|-
|-
|<small>[[EBMDR-8]]</small>
|style="text-align: center; vertical-align: top;"|[[EBMDR-8]]</small>
|<small>[[MB-30G]]</small>
|style="text-align: center; vertical-align: top;"|[[MB-30G]]</small>
|<small>[[EMMAR-1H]]</small>
|style="text-align: center; vertical-align: top;"|[[PAM1H]]</small>
|<small>[[EMBR-1]]</small>
|style="text-align: center; vertical-align: top;"|[[EMBR-1]]</small>
|<small>[[EMBR-2]]</small>
|style="text-align: center; vertical-align: top;"|[[EMBR-2]]</small>
|-
|-
|}
|}


== Related Information ==
==Software Requirements==
* [https://www.zenitel.com/product/ecpir-3p Additional Documentation on Zenitel.com]
This station is fully supported as from AlphaCom version 11.2.3.11
* Edge mode is supported from firmware version 5.0
* SIP (and Pulse) mode is fully supported as from firmware version 4.7
 
==Related Information==
 
*[https://www.zenitel.com/product/ecpir-3p Additional Documentation on Zenitel.com]


[[Category: Turbine]]
[[Category: Turbine]]

Latest revision as of 16:10, 3 January 2025

ACEIS icon.PNG
Exigo call panel (1023200033)

Getting started

Configuration

The device can operate in different modes. Set the mode according to the server the station should register to.

Note icon To use this device with Zenitel Connect Pro it must be factory defaulted. The device configuration is done from the Zenitel Connect Pro server.


Station specific configuration for the ECPIR:

Restore Factory Defaults and Software Upgrade

Connectors, Indicators and Dimensions

Accessories

EBMDR-8-newZ.png 3005020033.PNG 1023533012.png 1023595010.PNG 1023595020.PNG
EBMDR-8 MB-30G PAM1H EMBR-1 EMBR-2

Software Requirements

This station is fully supported as from AlphaCom version 11.2.3.11

  • Edge mode is supported from firmware version 5.0
  • SIP (and Pulse) mode is fully supported as from firmware version 4.7

Related Information

Retrieved from "https://wiki.zenitel.com/w/index.php?title=ECPIR-3P&oldid=239219"
MediaWiki spam blocked by CleanTalk.