Exchange & System (AlphaPro)
From Zenitel Wiki
Contents
Exchange and System
The Exchange & System window shows information about the exchange and the PC settings. The information can be edited from the System window or by double clicking the exchange in the listbox to the left.
| Exchange name: | The name was choosen when the database was created. Can be edited from the System window. |
|---|---|
| Description: | Here you can enter a more detailed exchange name (the text is stored in this PC, and is not sent to the exchange). Can be edited from the System window. |
| Node: | Default node number is 1. The node number is for communication between exchanges in AlphaNet. The node number was choosen when the exchange was created. Can be edited from the System window. |
| AlphaNet - Adm. here: | Enabled: The exchange was created with full database. Disabled: The exchange was created without database. The flag can be edited from the System window (as from version 10.40). |
| Cluster Node: | Cluster programming is a option to simplify programming and updating of numbers in AlphaNet when operating with integrated number series. Nodes with the same Cluster Node Number (1-255) are members of the same cluster. |
| Database Version: | Shows the database version for the FoxPro database used by the AlphaPro program. The information is automatically entered. |
| Node Type: | Reflects the choice you made when you created the exchange. It is possible to change node type in the System window. |
| Language: | Reflects the language choosen when the exchange database was created. This choice influences the display texts in the stations. |
| DMP File Id: | The name of the dmp file is DMP_x.DMP, where x is the DMP File Id. |
| PC Settings: | Shows information on how the PC connects to the exchange |
| 1st/2nd/3rd Slave IP: | Shows the IP address of the slave module(s) when MultiModule is used. If the Node Type is set to AlphaCom (and not AlphaCom E) it will change slightly, and instead show which modules are enabled. |
| Comments field: | Any additional information is shown here. Note that this information is not sent to the exchange, but is only stored in the PC. Can be edited from the System window. |
System
General
| Exchange name: | The name was choosen when the database was created. The name will be sent and stored in the AlphaCom exchange. The name can be edited from this window. |
|---|---|
| Description: | Here you can enter a more detailed exchange name (the text is stored in this PC only, it is not sent to the exchange). |
| Node: | Default node number is 1. The node number is for communication between exchanges in AlphaNet. The node number was choosen when the exchange was created. Can be edited from this window. |
| Cluster Node: | Cluster programming is a option to simplify programming and updating of numbers in AlphaNet when operating with integrated number series. Nodes with the same Cluster Node Number (1-255) are members of the same cluster. |
| Node Type: | Reflects the choice you made when you created the exchange. It is possible to change the node type from AlphaCom to AlphaCom E or vice versa after the database has been created. |
| AlphaNet - Adm. here: | Enabled: The exchange was created with full database. Disabled: The exchange was created without database. The flag can be edited from the System window (as from version 10.40). |
| Language: | Reflects the language choosen when the exchange database was created. This choice influences the display texts in the stations. |
| DMP File Id: | The name of the dmp file is DMP_x.DMP, where x is the DMP File Id. The information is automatically entered. |
| Database Version: | Shows the database version for the FoxPro database used by the AlphaPro program. The information is automatically entered. |
| PC Settings/TCP-IP Configuration: | Use TCP/IP to connect: Select if communication between PC and AlphaCom should be on ethernet or via Com-port Connect to port: Specifies which of the two ethernet ports of the AlphaCom the PC is connected to |
| 1st/2nd/3rd Slave IP: | IP address of the slave module(s) when MultiModule is used. If the Node Type is set to AlphaCom (and not AlphaCom E) this information will change slightly, and you can enable which modules are in use. |
| Comments field: | Any additional information might be entered here. Note that this information is not sent to the exchange, but will be stored in the PC only. |
Calls and Options
| System Options | |
| Duplex: Ignore High Frequency | The high frequency evaluation in the duplex algoritm can be switched off by setting this flag. This may be useful in surroundings with high frequeny noise from fans or aircondition, as the high frequecies might influence on the duplex voice switching. |
| Autonom Mode: Copy NVRAM | This option must be enabled if you want to run the slave modules in autonomy mode in case of communication break with the master in a MultiModule system. The configuration of the Master AMC board will be copied in the background to the slave AMC boards. |
| User SWAP Mode | The options are:
|
| Flags | |
| Group Hunt Rotate | The Group hunt can be programmed either to:
|
| Simultaneous Group Calls | Checked: Several group calls might be active at the same time if there are no overlapping members. When several group calls are active simultanously, a group call can only be answered from a station belonging to the group.
Note that the "gong" is a common resource for all groups and can only be used by one group at the time. Unchecked: It is not possible to have more than one active group call at a time. |
| No Group Calls In Conversation | When enabled no group call audio will be received when a station is active in a conversation. |
| Mute Program During Group Call | By default Audio Program and group call audio is mixed. When enabled the Audio Program will be muted when a group call is received. |
| Ignore Station Down In Conversation | If a station is reported faulty while in conversation the conversation will not cancel. Might resolve a problem experienced with some older substations which cancels the call immediately after connection. |
| Wake Up Call | |
| Duration | Duration of private ringing for Wake-up Calls |
| Repetition | Number of times the Wake-up Call is repeated if not answered |
| Interval | Time between repetitions |
| Hotline | |
| Hotline Call Delay | The time from the handset is lifted till the hotline number is dialed. During this time it is possible to use the keypad for ordinary dialing. If all telephones/stations with the hotline option are going to be used for hotline dialing only, set the delay to 0. Autoload = 5 sec. The Hot-Line feature must be enabled per station in the Users & Stations > Station Type window. |
| "Priority Mail" Queue Indication | |
| Minimum Priority Level | This value is linked to the events Priority Mail Present and Priority Mail in Idle, and sets the minimum priority level required to trigger these events. |
| Private ring mail priority | When receiving Mail or Call Request with this priority or higher, the receiving station will be alerted by a private ringing tone. Default priority level is 150. Also ATLB subscribers (telephones) can receive this type of Call Requests, as the telephone will start to ring when a call is received. |
| Call Forwarding | |
| Ring Count | Number of private ringing signals on the station before the call is transferred. When set to 0 the call will be transferred immediately, without any ringing signal heard in the station. |
| Urgent Feature Reminder | |
| Pulse Count | The number of "dut-dut-dut-dut" tones when receiving Call Request (or any other mail) with priority 120 or more. Usually triggered by the call request code 622. See also Urgent feature reminder |
| Pause Between | The interval between the Urgent feature reminder tones |
| Conversation Timeout | |
| Enable | By default all converations are cancelled after 1 hour 49 minutes. Uncheck this flag if conversation timeout is not wanted |
| Timeout | The conversation timeout can be modified. Max. time is 6540,0 seconds (1 hour 49 minutes) |
Logs and Errors
| System Logging to Printer/PC Select what to report to the System log | |
| Line Error | Analog station: Short-circuit or break on audio wires IP Station: Communication error between AlphaCom E and IP station |
| Board Error | Any board error detected by the AMC-IP |
| Device/CardCage Error | Includes the following devices: |
| Software Reports | Various messages during start-up and normal operation, see System log for more details |
| RCI ON/OFF | Report when RCI inputs goes ON or OFF |
| Line Monitoring | |
| Extended Wire Check | Check for break in c- or d-wire even if ab-wires are OK. When a station is tested the LED will flash for a short period. A break in c/d-wire will be detected within approx. 1.5 to 6 minutes, depending on the number of stations connected to the system. Stations are tested one by one in a rotating fashing. The test uses 0.5 sec per station connected and 0.1 sec per station not connected. After having tested the last station in the loop there is a 23 second delay before the test starts again from the beginning. |
| Enable Tone Test | Activate the periodic Tone Test. The manual tone test can be activated independent of periodic tone test. |
| Start time, Tone Test | Enter the time (24-hour notation) when the tone test should start |
| End Time, Tone Test | Enter the time (24-hour notation) when the tone test should stop. If start and stop time are set to 0, the tone test runs continuously. |
| OffHook Too Long | For stations without display off-hook is not possible to separate from break in ab-wire. A station error is reported if the handset is off for more than the time specified here, and no dialling takes place. Default = 1 hour. |
| AlphaNet Audio Test Period | Interval between tone test of each AlphaNet audio line (Relevant for AGA or AE1 lines only). Value 65535 will disable the test. This may be necessary in installations with multiplexes with echo cancellation or heavy voice compression, where the tone test may fail and cause an AlphaNet line error. |
| System Log and Error Reports to | |
| Node 1 + Device 1 | When an exchange generates an error message, it can be sent to one or two destinations. Enter the node and device number to which System Log events should be sent. Default value is 0 + 0, which means report to own log port. Example: 4 + 65 means forward system log events to node 4. |
| Node 2 + Device 2 | Forward System Log reports to remote node and device. Default value is 0 + 0, which means report to own log port. Example: 4 + 65 means forward system log events to node 4. |
| Broadcast event messages to remote node | ACDP broadcast messages will be forwarded to the specified node. Useful for Call Handler applications like AlphaVision used in AlphaNet, which relies on status information received from each individual AlphaCom exchange. |
Timers
| Voice paging answer wait time: | Answer time after a Group Call or All Call. |
| Voice Paging Message Wait Time | Time from a Group Call or All Call is made till the M-key must be pressed. |
| Call Request/Busy Notify Display Time | The time a Call Request Message or a Busy Notify Message is displayed at the receiving station. |
| Call Request Reminder Time | The ringing time for a (sub)station which has made a Call Request |
| Camp On Busy Time | If a station or a feature is busy you will hear a "busy" tone and the display will show "Busy". If the station or feature becomes free within this preset time limit (default 30 seconds), you are automatically connected (Camp on Busy). |
| Private Call Time | Sets the timeout for calls in Private Ringing mode. |
| Auto Search Time | A call in private ringing mode will be transfered to the search list of the called station after this time (default 11 seconds) if the auto-search feature is enabled. |
| RCO (door open) Pulse Time | The time the RCO signal is active for the event types Door Opening during connection and Automatic lock. |
| Call Request search string Timeout | Forward unattended Call Requests to the search list after this time (default 20 seconds) if the auto-search feature is enabled. |
Fire Alarm
| AlphaCom ESPA 4.4.4 Address | Link address in the ESPA 4.4.4 protocol for communication for AlphaCom. Is used for communication between AlphaCom exchange and the Fire Alarm Control Panel. The value is by default set to 50. |
| Fire Panel 4.4.4 Address | Link address in the ESPA 4.4.4 protocol for the fire alarm panel. Is used for communication between AlphaCom exchange and the Fire Alarm Control Panel. The value is by default set to 49. |
| Supervisor Station | The station receiving the pre-alarm message. |
| Nearest Station | When a prewarning message is displayed at the supervisor station, pressing 8 at the supervisor station sets up a connection to the station closest to the Fire Alarm Control Panel. |
| Pager Driver | The following options are available:
|
| Fire Team (Group Number) | The group receiving the Fire Pre-Alarm and the Fire Alarm messages to their pagers. |
VoIP
| Flags | |
| Use VolP Audio for Multi Module | Disable this flag when using AGA or AE1 for audio distribution in MultiModule, and not VoIP. Note that it is also possible to use a mix of VoIP audio and conventional AGA/AE1 links. Then this flag must be enabled. |
| Optimized voice duplex control when conversation with SIP trunk/station | When calling SIP there can be problems with the standard duplex algorithm due to DSP echo cancelling in the SIP station. A new duplex algorithm is available for duplex towards SIP stations that is speech controlled only from volume of the microphone signal from the SIP link. When this flag is set, the initial voice direction is forced to be from the intercom towards the telephone. When the phone operator starts to speak, the voice direction will switch towards the intercom station, regardless of the level of the audio signal from the intercom station. As soon as the phone operator stops speaking, the voice direction will switch back to the initial direction. |
| Incoming calls from SIP in Private Ringing mode | When enabled incoming calls from SIP trunk line or SIP phones will be forced in private ringing mode, regardless of the private/open switch of the intercom station. |
| Use UK style Ringing Tone on Ringing Group Calls from SIP | On: When a Ringing Group is called from SIP Trunk a special ringing tone is used. This is to distinguish external phone calls from internal calls. One can choose between different tone types:
Off: Regular Private Ringing tone also from SIP calls. |
| Timers | |
| Max VolP round Trip Delay allowed for open duplex during handset conversation in AlphaNet |
AlphaNet calls: The roundtrip delay on a VoIP AlphaNet conversation is measured by the AlphaCom. If the delay is more than the value specified in this parameter, a handset to handset conversation will be forced in voice switched duplex. This is to prevent echo in the handset due to crosstalk in AlphaCom handset (and no echo cancelling). |
| SIP digit collection timeout: | Specifies how long the AlphaCom should wait for more digits before setting up the connection to a SIP device. The timeout is used by feature 81 and feature 83 when the field "Collect N more digits (SIP)" is used. |
| SIP Dial Delay | After having made a connection to a SIP gateway, further dialing is delayed by the time specified by this timer. |
| Group Calls, Audio Program to IP stations | |
| Base Address | First multicast address used by this node. Default is empty. If empty the address 239.192.nnn.0 is used, where nnn is node number. Usually this default can be used. Only need to be changed if conflicts with other multicasting applications on the same net. Alphacom may use up to 31 adresses following the base-address. These adresses are used for group call, program conference and audio program to IP stations. |
| Audio Program feed in master | When this flag is enabled Audio Programs need only to be connected to the master in a MultiModule. When the flag is disabled Audio Program must be connected in parallel to all modules, as before. Exchange reset is needed after changing the flag. |
| Default rule | Determine how Group Audio is transmitted to IP stations. The default rule is a two-way choice:
This rule applies to all IP stations which do not match any of the subnet rules 1 - 5. See also Multicast in AlphaCom |
| Subnet rule 1 - 5 | Up to 5 Subnet Rules can be defined to make exceptions from the Default Rule.
A Subnet Rule applies to IP stations with IP addresses within a given range. The IP address range for the rule is defined using the IP-address + subnet-mask scheme familiar from IP routing tables, see http://en.wikipedia.org/wiki/Subnetwork . A dropdown list with three alternatives tell how each of the 5 subnets are handled :
After changing the Subnet Rules, AlphaCom has to be reset. When a station registers with the AlphaCom, AlphaCom checks the 5 rules in turn to find a address match. The search stops when the first match is found. This means that it is possible to specify a rule with a narrow address range, followed by a different rule for a address range which is superset of the first rule. Stations which do not match rule 1, but rule 2 will use rule 2. |
UDP Text
The User Defines Properties (UDP) are defined in three steps:
- You define the text (names) for the properties (from this window)
- You allocate properties to the stations (from Stations - UDP)
- You set up the behavior of the User Defined Properties (from the Event Window).
Note: that if the exchange is part of an AlphaNet installation, the UDPs should have identical programming in all exchanges.
RCI
Inputs
| Descrption | Description Missing |
| Device number | 1 - 64 = External devices like RIO - matches address switch setting on the RIO board; see AlphaCom Installation Manual, A100K10002.
65 = Exchange |
| Pin number | APC board - 1 - 6 (device number 65) RCO - 1 - 8 on each RIO unit (the units must have different device numbers) See pin number overview in Appendix from page 237 onwards.
|
| On Action | Enter the command for the action to take place when the RCI input is turned on. It is possible to have several commands separated by semicolons <;>. |
| Off Action | Enter the command for the action to take place when the RCI input is turned off. It is possible to have several commands separated by semicolons <;>. |
| On When Closed | Generates alarm on closed or open contact
Normal Open (NO) Normal Closed (NC)
|
| Delay ON Action | The time from the RCI is activated to the action is carried out. If the RCI in the waiting time is deactivated, the action is not carried out. Value is shown in 100 msec units. Maximum value 65 000 = 1 hour 48 minutes. This can be used for two purposes:
Stabilizing of the line, to debounce any unwanted signals. For example, used with an alarm button in a lift. The button will have to be pressed down for a certain time to activate the alarm signal. Thus an unintended short press will be ignored. |
| Activate Faulty Module LED | Description Missing |
Faults
| Descrption | Description Missing |
| On Action | Description Missing |
| Off Action | Description Missing |
Serial Ports
| Enabled | Description missing |
| Port Type | Description missing |
NetAudio
| Source | |
|---|---|
| Source | Description Missing |
| Discription | Description Missing |
| Physical No: | Description Missing |
| Mod | Description Missing |
| Pos | Description Missing |
| Line | Description Missing |
| Destination | |
| Destination | Description Missing |
| Description | Description Missing |
| Mod | Description Missing |
| Pos | Description Missing |
| Line | Description Missing |
| Channel No. | Description Missing |
Ping
Board
| Module, Board, Port | Is entered automatically by AlphaPro according to the highlighted port |
| Physical Number | The physical position where the relevant AGA board is installed - see Appendix page 229 for board positions. |
| Port use | The following options are available:
Default - uses the default setup for AGA board; see Appendix page 229 for functions of AGA board in different positions Station - this option is intended for connection of audio equipment not using the audio interface on the ASLT board. Typically this option can be used to connect a mobile radio system without using the FBSAR board. The equipment is treated like a station in the AlphaCom system Multiconference Monitor - is used with the multiconference feature. Reserved 5 - for special purposes.
|
Events
| Owner | |
|---|---|
| Owner Type | The options are:
reflects the station’s physical number. If you come from the station screen to the event screen, the field is set to the current station and cannot be changed. If you come from the system window to the event screen, you can fill in the owner field for any station or User Defined Properties UDP. Note that when the entry has been saved, the owner field cannot be changed. The event owner is always within your local exchange.
is used when a group of stations with identical properties should react to an event. |
| Event | |
| Event Type | What exchange event should cause the action. The drop-down list gives all possible exchange events, 01 - 19, see details in the Event List on page 94 |
| Sub event | Some events have a subtype. Audio events: the number here is entered when you activate the different flags. |
| Details | Click Flags to get access to the flag help. Sets the event subtype. Also see details in the Event List on page 94. |
| When change to | The action is executed at a specific event transition, i.e. when the defined event goes on and/or off. The options are:
Always Default value. Both ON and OFF transitions match. |
| When Related to | *All
The event is carried out with no check on the related number, i.e. works for all stations. Many events have no related number available, and in that case the field is not available.
The action is executed when the event owner is connected to the defined station/feature. The id field is two-part:
The action is executed when the event owner is connected to any station with this User Defined Properties UDP. The id is a property flag 1 - 8. |
| Action Command or RCO | |
| Action Command or RCO | *Upper radio button = Command. You use a defined set of command strings; see the table below. Press the button “Action ?” at the top to display help for the command strings on the screen. It is possible to do a copy/paste from the help window to the command field in this window.
Here you define the RCO output you want to activate for the defined event. |
RCO
| RCO number | Description...Dream on, honey! |
| Description | Can help to identify the RCO outputs. Is only used by AlphaPro and will be reflected in the listbox to the left. The information is not sent to the exchange. |
| RCO type | Description is gone!! |
| Device | 1 - 64 = External devices like RIO - matches address switch setting on the RIO board. Each unit must have a unique device number.
65 = Master Module |
| Pin number | Each ASLT board provides 6 RCOs. See table in Appendix on page 237.
ASLT/ATLB boards: For Device 65 pin 1 - 138 is possible |
Devices
| Device Number | Reflects the choice highlighted in the listbox to the left. |
| Description | Here you enter the device name, max. 22 - 36 characters. The name is used in the listbox to the left. The information is not transferred to the exchange, but stored in the PC file. |
| Device Type | There are five options:
|
| Data [ACDP Link]: | Lists the serial ports numbers with the default drivers for the ports. Overview of the serial ports settings - see page 187. |
NetRouting
| Source | ||
|---|---|---|
| Source | Description missing | |
| Description | Description missing | |
| Destination | ||
| Destination | Description missing | |
| Description | Description missing | |
| Primary Route | ||
| Data - ACDP Link | Description missing | |
| Data - Node Number | Description missing | |
| Audio - Node Number | Description missing | |
| Alternative Route | ||
| Data - ACDP Link | Description missing | |
| Data - Node Number | Description missing | |
| Audio - Node Number | Description missing | |