Message Formats (Sortable)

Click on the header to sort on that column.

Message	Short name	Message no, Hex	Description
ABSENCE_STATUS		0x002A	Response to SET_ABSENCE and GET_ABSENCE messages
ALARM_MSG	ALRM	0x0007	Set up (or disconnect) an ASVP Alarm message to a single station or a predefined group of stations
ALARM_MSG_ACK		0x0009	Positive response to ALARM_MSG
AUDIO_CH_DISCON		0x8012	Disconnect a audio channel after loopback test
AUDIO_CH_FAULTY		0x8013	Response to AUDIO_CH_LOOPBACK_REQ: Requested channel was faulty
AUDIO_CH_LOOPBACK_ACK		0x8011	Positive acknowledge of AUDIO_CH_LOOPBACK_REQ
AUDIO_CH_LOOPBACK_REQ		0x8010	Request for loopback audio connection. Used by the Audio Channel Testing process
AUDIO_CH_TONE_REQ		0x8015	Request a peer exchange to put a 500Hz tone on a audio channel
AUDIO_CODEC		0x801D	Message sent in the direction of start node, from end node or trans-coding nodes along the path
AUDIO_DETECT	VOX	0x0053	Triggers the event Simplex_Conference_Audio
AUDIO_LINK_NOT_AVAILABLE		0x8006	Response to AUDIO_PATH_SETUP from next node: Channel not granted
AUDIO_LINK_OK		0x8003	Response to AUDIO_PATH_SETUP. Channel number is OK
AUDIO_LINK_RELEASE		0x8005	Used to release audio path backwards stepwise from node to node when setup meets busy or faulty link
AUDIO_M_FEED_REQ		0x801A	Global Simplex Conference: Some station is pressing the M-key when participating in a conference
AUDIO_M_FEED_STOP		0x801B	Global Simplex Conference: The station is releasing the M-key
AUDIO_M_LINK_OK		0x8019	Per­ hop positive response to AUDIO_M_PATH_SETUP
AUDIO_M_PATH_BACKTRACK		0x8018	AUDIO_M_PATH_SETUP failed
AUDIO_M_PATH_OK		0x8017	Contains statuses for an AUDIO_M_PATH_SETUP from one or more destination exchanges
AUDIO_M_PATH_SETUP		0x8016	Communication in a multi-node network
AUDIO_PATH_CHECK_OK		0x800F	Positive response to CHECK_AUDIO_PATH
AUDIO_PATH_DELAY		0x8007	Set Duplex switch delay
AUDIO_PATH_DISCONNECT		0x8006	Release the end­to­end audio path. Normal disconnect from source or destination
AUDIO_PATH_OK		0x8002	End to end message: Audio path is ready
AUDIO_PATH_SETUP		0x8001	Set up audio path between a source node and a destination node (possibly via transit nodes)
AUDIO_PATH_STATE		0x801E	SIP Response to AUDIO_PATH_SETUP
AUDIO_RTP_DTMF_DIGIT		0x8021	Rfc4733 RTP digit event send or receive
AUDIO_RTP_DTMF_SETUP		0x8020	Set up reception of rfc4733 digit events in RTP.
BUILD_GLOB_GRP		0x0070	Broadcast message to all exchanges to make them rebuild global group indexes
C_KEY	C	0x0058	Order station to press C-key
CAC		0x00A9	Cancel All Conversations
CALL_SETUP	CALL	0x0008	Sets up a conversation between two users
CALL_STATUS_BC		0x0040	Broadcast message telling the status of a call
CALL_TRANSFER	TRF	0x0044	Set or remove call transfer for a station
CALL_TRANSFER_NOK		0x0046	Negative response to CALL_TRANSFER
CALL_TRANSFER_OK		0x0045	Positive response to CALL_TRANSFER
CANCEL_MAIL	CANM	0x0065	Delete one or more mail/call request/alarm messages queued at a station
CDC_CMD		0x009F	Used for Billing ABSD->AMCD
CDC_STATE		0x009E	Used for Billing AMCD->ABSD
CFG_UPD		0x00A1	Signal update of configuration tables.
CHECK_AUDIO_PATH		0x800E	Check of established audio path at regular intervals
CHILLY_RESET		0x0039	Simulates Chilly Reset sent from ICX-AlphaCom web interface
CLEAR_RCO	CLR	0x0015	Turn the given remote control output off
CLEAR_RCO_FAILED		0x0017	Negative response to the CLEAR_RCO message
CLEAR_RCO_OK		0x0016	Positive response to the CLEAR_RCO message
COMMAND_RESPONSE		0x0066	General response message to messages
CONN_2_GROUP	C2G	0x00B0	Connect the audio from a group to the speaker of the group
CONF_IS_ROOT		0x007B	Broadcast message. Sender informs that it is root of conference
CONF_JOIN		0x0078	Exchange wants to join conference, asks root-exchange to setup connection back to sender
CONF_MEMB_CHK		0x0079	Ask whether any neighbor exchange has any ordinary member left in conference
CONF_NOT_ROOT		0x007C	Broadcast message. Sender informs that it is no longer root of conference
CONF_ORD_MEMB		0x007A	An exchange tells its neighbors that it has ordinary member left in conference
CONF_TALK		0x008B	Set Simplex conference speaker
CONF_TALK_STOP		0x008C	Stop station form feeding Simplex conference
CONN_REF_ACK		0x000E	The external application acknowledges the CONN_REFERENCE
CONN_REFERENCE		0x000B	Positive response from the exchange to CONN_REQUEST
CONN_REQUEST	CONN	0x000A	Sets up a coversation between two users
CONN_STATUS_BC		0x0041	Broadcast message telling that a connection is established
CONSOLE_DISC		0x007F	Log off from system debug console (TST)
CONSOLE_REQ		0x007E	Log on to system debug console (TST)
COPY_MAIL	CPYM	0x0083	Send a copy of a mail in own queue to a new destination (station or group)
D2S		0x00B4	Send key press to a AlphaCom registered SIP station.
DELETE_MAIL	DELM	0x0034	Delete a mail entry in the queue for an intercom station
DELETE_MAIL_ACK		0x0035	Response to the DELETE_MAIL message
DEVICE_INFO		0x003B	Response to the GET_DEVICE message
DIAL_DAK		0x0094	Dial DAK on a station
DIAL_DIGITS	DD	0x0050	Simulate digit dialing from a station
DIGIT_RELEASE	DREL	0x0052	The station has released a digit press
DIP_FWD	DIP	0x00A0	Send DIP messages to IP stations
DISC_REQ		0x0011	Conversation established with CONN_REQUEST: The external application disconnects a conversation.
DISC_REQ_ACK		0x0012	Conversation established with CONN_REQUEST: The AlphaCom acknowledges the DISC_REQ message
DISCON_ST		0x008E	Disconnect station from ongoing feature
DISCON_STATUS_BC		0x0042	Broadcast message telling that a connection is disconnected.
DISCONNECTED		0x000F	Conversation established with CONN_REQUEST: Conversation was disconnected, e.g. the user pressed C-key
DISCONNECTED_ACK		0x0010	Conversation established with CONN_REQUEST: Acknowledge of the DISCONNECTED message
DISPLAY_TEXT	DSPL	0x005A	Send text and control characters to a station
DPMT_INVALID		0x0000	Reserved value for internal use
DTMF_CONN		0x0097	Generate DTMF tone during conversation (Only during conversation with RingMaster)
DTS		0x00B2	Update display text on station.
DUMMY		0xFFFE	Test message: Should be routed, accepted and ignored
EC_STATE		0x0093	Update remote node of the Echo Canceler state of station.
EVENT_REPORT	ER	0x0067	Report an event to the event/action system
EXECUTE_COMMAND	X	0x004F	Send a command string to the exchange to be executed there
EXT_FEATURE_BC		0x0043	Broadcast message when a directory number (feature 50) is dialed on a station
EXT_MAIL		0x0030	Response to the GET_x_MAIL messages
GET_ABSENCE	GABS	0x0029	Get absence status for an intercom station
GET_DEVICE	GDEV	0x003A	Get information from an external device
GET_FIRST_MAIL		0x002E	Get the first mail entry in the queue for an intercom station
GET_LAST_MAIL		0x0064	Get the last mail entry in the queue for an intercom station
GET_NEXT_MAIL		0x002F	Get the next mail entry in the queue for an intercom station
GET_PIN_COUNTS	GPC	0x0013	Query a RIO about number of output and input pins and support for non mandatory features
GET_PREV_MAIL		0x0063	Get the previous mail entry in the queue for an intercom station
GET_REQ_TRANSF		0x002C	Get the Call Request Transfer status for an intercom station
GET_SYSTEM_TIME	GTS	0x0025	Ask a device (AlphaCom) for date and time
GET_THIS_MAIL		0x004A	Get the identified mail entry in the queue for an intercom station
GLOB_GRP_MEMB		0x006A	A exchange tells which global groups this exchange is member of by broadcasting this to all exchanges
GROUP_MEMBERSHIP	GRM	0x0081	Set group membership in NVRAM for a station
GROUP_MSG	GM	0x00A6	Start SVP message playback to group
GROUP_MSG_STOP	GMS	0x00A7	Stop SVP message playback to group
HANDSET_OFF	HOFF	0x0056	Order station to lift handset
HANDSET_ON	HON	0x0057	Order station to replace handset
HS_SIDE		0x00A2	Turn handset sidetone on/off
ILLEGAL_PARAM		0x0023	Negative response
LOG_STRING	LOG	0x0075	Output String to System Log
LOOPBACK_IMPOSSIBLE		0x8014	Response to AUDIO_CH_LOOPBACK_REQ
M_KEY	M	0x0054	Order station to press M-key
M_KEY_RELEASE	MREL	0x0055	Order station to release M-key
MAILQ_NAVIG		0x008D	Do operation on mail queue, or step current mail in mail queue
MODIFY_COS_CONTENTS	MCC	0x0091	Modify feature membership in COS in NVRAM
MVO		0x00A8	Mask volume and handset override ON/OFF
NAME_EXTENSION		0x0080	Special exchange mode using two line names: Send the second line through AlphaNet
NO_ACCESS		0x003F	Negative response to CONN_REQUEST
O_DUPL_CONF	ODC	0x006F	Include/exclude a station or a group into/from an Open Duplex Conference
OD_CONF_ENTERED		0x0076	The participant has entered an Open Duplex Conference
OD_CONF_LEAVE		0x0071	The participant has left the Open Duplex Conference
PA_CMD		0x00AE	Acknowledge and remove IP-ARIO PA failure states.
PARK_INQ_BROKER	INQ	0x0086	Park station from conversation, enter Inquiry call state
PAR_RING		0x0098	Add a Parallel Ringer station to a call in ringing state
PIN_COUNTS		0x0014	Response to the GET_PIN_COUNTS message
PING		0x003C	Test device: “Are you there?”
PLAY_DAK	PD	0x009C	"Dial sequence" for playback.
POLL_RCI	POLL	0x001D	Poll the given remote control input once
PONG		0x003D	Response to the PING message. “Yes, I’m here.”
PROG_CONF	CONF	0x0004	Set Simplex conference for predefined group of stations or a single station
PROG_CONF_ACK		0x0006	Positive response to PROG_CONF
PROG_CONF_NAK		0x004E	Negative response to PROG_CONF
PROGRAM	PROG	0x0001	Set audio program for single station or a predefined group of stations
PROGRAM_ACK		0x0003	Positive response to PROGRAM
PROGRAM_NAK		0x004D	Negative response to PROGRAM
PULSE_RCO	PULS	0x001B	Generate a pulse with the defined length
PULSE_RCO_FAILED		0x0022	Negative response to the PULSE_RCO message
PULSE_RCO_OK		0x001C	Positive response to the PULSE_RCO message
PUT_STRING		0x0073	Output String to Exchange serial port after adding appropriate framing depending on selected port
Q_ELEM_ADDED		0x004B	Broadcast message. Reports that a mail message has been added to a station’s mail queue
Q_ELEM_REMOVED		0x004C	Broadcast message. Reports that a mail message has been removed from a station’s mail queue
R_KEY		0x00A4	R_KEY signal
RCI_CHANGED	RCIC	0x0084	New RCI state reported from the exchange
RCI_IS_OFF		0x001E	Response to the POLL_RCI and SCAN_RCI_ONCE messages, input pin is off
RCI_IS_ON		0x001F	Response to the POLL_RCI and SCAN_RCI_ONCE messages, input pin is on
RCO_CHANGED	RCOC	0x0085	New RCO state reported from the exchange
REC		0x00B3	Start and Stop recording (Recording on demand)
REQ_TRANSF		0x002D	Response to the SET_REQ_TRANSF and GET_REQ_TRANSF messages
REQ_TRANSF_CALL	TRFC	0x0088	Transfer call in an Inquiry Call situation.
RESET_AUDIO_LINK		0x8000	Reset audio link between nodes
RESET_DEVICE	RESET	0x0039	Reset a device
RESET_TAKEN	RSST	0x0038	A device reports that it has done an internal reset
RESOURCE_BUSY		0x003E	Negative response to CONN_REQUEST
ROUTE_ALPHAPRO_MSG		0x006E	Send AlphaPro message via AlphaNet to/from a remote node
SC		0x00B8	Set station in silence call mode for next feature activated
SCAN_END_ACK		0x0024	Acknowledgment to the RCI_IS_OFF and RCI_IS_ON messages
SCAN_RCI_ACK		0x0021	Positive response to the SCAN_RCI_ONCE message
SCAN_RCI_ONCE	SCAN	0x0020	Scan input until defined condition is met, then report to exchange
SEND_MAIL	SM	0x0031	Send a mail message to an intercom station
SEND_MAIL_ACK		0x0033	Response to the SEND_MAIL and SEND_TEXT_MAIL messages
SEND_TXT_MAIL	STM	0x0032	Send a mail message with free text to an intercom station
SET_ABSENCE	SABS	0x0028	Set absence status for an intercom station
SET_CALL_REQ_MODE	SCRM	0x006C	Turn on/off message “your call is registered, please wait”, then ringing/flashing at a station
SET_DIRNO_TXT	SDT	0x0077	Change the display text of a directory number (station or feature)
SET_GRP_FILT	GFLT	0x007D	Set group call filter for a station
SET_IPRCO		0x00AD	Set a physical RCO on IP station or IP-ARIO
SET_LOGICAL_RCO	SLRC	0x006B	Set or clear a logical RCO
SET_MAIL_TIMEOUT	SMT	0x0082	Set the timer of a mail queue entry
SET_NODE_NUMBER		0x006D	Change the node number of an exchange
SET_RCO	SET	0x0018	Turn the given remote control output on
SET_RCO_FAILED		0x001A	Negative response to the SET_RCO message
SET_RCO_OK		0x0019	Positive response to the SET_RCO message
SET_REQ_TRANSF	SCRT	0x002B	Set transfer of Call Request for an intercom station
SET_STATION_COS	SSC	0x0090	Set COS membership in NVRAM for a station
SIMP		0x00A3	Set conversation in simplex
SET_SYSTEM_TIME	SST	0x0027	Set the internal clock to the given date and time
SET_TIMER	ST	0x008F	Start or stop a timer
SINGLE_DIGIT	DIG	0x0051	Dial one digit on a station
SNV	SNV	0x0095	Update specific system settings (NVRAM) values
SMALL_RESET		0x00BC	Simulates Small Reset sent from ICX-AlphaCom web interface
ST_AUDIO_OPT		0x00AB	Control audio options of station in connection.
ST_BUSY_BC		0x0036	Broadcast message: Intercom station is busy
ST_FREE_BC		0x0037	Broadcast message: Intercom station is free
ST_GROUP_DISCON	SGD	0x0074	Switch off Group Call audio at a station that receives Group Call audio at the moment
STATION_EVENT_BLOCK	SEB	0x00B1	Allow blocking of events from IP station
STATION_BUSY		0x000D	Negative response to CONN_REQUEST.
STATION_CONVERSATION		0x0060	Message from remote exchange. Set station in conversation mode. Stop tone and open mic.
STATION_DOWN		0x000C	Negative response to CONN_REQUEST
STATION_INFO		0x801F	SIP update of number and display text
STATION_LISTEN		0x0061	Message from remote exchange. Set station in listen mode. Shut mic
STATION_TRANSFER		0x0062	Message from remote exchange: Transfer of B subscriber.
STATUS_REPORT		0x0072	Report equipment Presence and Error/OK status
SVP_ST		0x00AC	Start playback of a message during conversation
SYNC_FLASH		0x00A5	Dump local database to flash file system
SYSPARAM		0x00B5	Set and read system parameter
SYSTEM_TIME		0x0026	Response to the GET_SYSTEM_TIME and SET_SYSTEM_TIME message
TEMP_PROG	TPROG	0x0096	Temporarily "mute" program distribution to a station
TRUNK_SIG		0x00B7	Activate backward digit signaling on SIP trunk.
UNPARK		0x0087	Unpark station from Inquiry call state station, return to conversation
UPD_MAIL_TIMEOUT		0x009D	Used for Ringing Group to update mail timeout in AlphaNet
VCP_MEET_REQ		0x0069	Request answer to global group call
VOIP_AUDIO_CONFIG	VAC	0x00AF	Configure the RTP stream station
VOL		0x009B	Set station volume
WAKE_UP		0x0047	Register or remove wake­up request
WAKE_UP_ACK		0x0048	Positive response to WAKE_UP
WAKE_UP_NAK		0x0049	Negative response to WAKE_UP
WRITE_USER_DEF_DATA	WUDD	0x008A	Write User Defined Data (UDD)